Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
i made custom board refer to thingy 52 Circuit
all fuction circuit is same so i want to use thingy 52 firmware
when i was erase all memory nrf52832 and upload thingy_v2...
I am using nrf52832 sdk14.2.0 to develop now, I want to realize the following function on the basis of PWM_driver example, output the following waveform on P0.22: 1ms high...
Hi all,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello,
I'm doing some power evaluation of the three PHYs of BT5 using the PCA10056 preview (v0.9.0) and the PPK (rev 1.1.0), moreover I'm using the ble_app_att_mtu_throughput...
I've seen variations on this question, but never quite been able to decipher a complete answer:
I've built an app for the NRF52DK based on the nRF5_SDK_15.0.0 "Hello World...
i created a mesh network using light_demo in NRF52832SDK and i need to scan a new device to make it join my mesh network .when there are a number of devices and i have to...
Hi,
I am working on the port of the nrfutil library of python -> C and I am looking for a support to understand the python code of the nrfutil library please.
Can you...
Hi
I was designing nrf52832 based PCB and using Jhonson's 2.4ghz antenna. The PCB is 2 layer and I am following the guidelines of chip antenna as given in the datasheet...
Hello:
We had a main application with NRF_LOG using RTT as its backend, and it was working great. We are using the BLE_DFU and recently added NRF_LOG capabilities to this...
Running through the ble uart example, connecting to the nRF connect app on my android phone. If I'm not actively sending data the bluetooth connection will time out on the...
Hi team, I am using nrf52 sdk 14, nrfjprog version: 9.7.3 and JLinkARM.dll version: 6.14c,getting this issue while flashing:
ERROR: JLinkARM DLL reported an error. Try again...
Hi all,
I have a functional FW, which is running properly 99 % of the time. But sometimes I have some RESET with RESETREAS register set to SREQ, but I'm not able to find...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
I am working in sdk15 nrf52832 ble_app_hids_keyboard.
I want merge ble_app_uart_c ,so modify in
sdk_config.h :
NRF_SDH_BLE_CENTRAL_LINK_COUNT 1
PM_CENTRAL_ENABLED...
