At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello,
I want to change data channels after provisioning, I follow devzone.nordicsemi.com/.../ here.
To set,
memset(&new_opt_config, 0, sizeof(new_opt_config));...
Hello Sir,
I am using nRf52832 s132, i want to write program which is automatically ON from sleep mode and after few second it will go system off mode for 1hr.
How i can...
Hi,..My device generated PWM square waves. I can program the frequencies and delays that is desired. but how to modulate current as per our requirement. I need the current...
Hello, I have recently bought a couple of boards from eBay that come with the nRF58232:
https://www.ebay.com/itm/Wireless-Bluetooth-Transceiver-Module-NRF52832-Development...
hi guys,
Can you please tell me what is happening when a smart phone trying to connect to nrf51822? Any event I could use? Would the connecting process has any impact on...
Hi,
I've just got my hands on this amazing little thing call Thingy 52. I have played around with the default app but now I'm struggling with flashing a custom firmware...
Hello,
I am trying to setup two Thingys with my node-red system and i have ran into some problems. The thingys respond to normal command line tools like gatttool, btmgmt...
Hi All,
I am new to Nordic microcontrollers. I am using keil uvision MDK lite version. After I have uploaded a source code and when i am trying to compile. I am getting...
Hello,
I am starting a new thread concerning the two messages that I have posted about generating a 4MHz clock on nRF52832. I am using the nRF5_SDK_14.2.0_17b948a SDK. ...
Hi,
if I correct understood DFU process first of all it need to send "Init packet" and after that it need to send FW image. And for that reason in DFU packages is 3 files...
Sir, i am looking to design customized board using nrf52832, i have pca10040 borad as well. i am looking for eagle library of antenna used in pca10040 (i.e nrR52DK).
if...
Hi, I'm trying to program a nRF52-DK, with a workong firmware, and a board that was working, but I can't manage to flash the DK.
With a make flash_softdevice:
Flashing...
I am working on nrf52832 BLE. I have used soft device s132. Antenna device is as per the reference design of NRF52832 and have used 32MHZ crystal for HFXO oscillator. but...
I am starting analysis for project of BLE Central device that is only receive broadcasting packet (advertise) from peripherals.
However, it’s unclear to me. I doubt will...
I notice that the sensitivity for the nRF52832 is defined as being ~2dB better in BLE mode than in NRF mode. I have also tested this to be correct.
However, I wonder - is...
