At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I just implemented LESC Numeric Match on the NUS service for my peripheral device (based on ble_app_multirole_lesc example). I am able to connect to my device using...
I am using the esb_tx example on an nRF51 DK board modified to send BLE advertising packets at 1 KHz.
I am receiving the packets on a BlueTooth sniffer. The contents of...
Hi,
i'm designing a board based on NRF51822-QFAC chip and i'm using this antenna chip 2450AT43A100E and this balun 2450BM14E0003T .
I put the balun as close as possible...
I have __asm("BKPT #0\n") in my code. When running without a debugger, it seems to generate a hard fault exception (which I can tell because I have a hard fault handler that...
This week I worked myself to a series of what seemed to be problems boiling down to one issue:
The Notification Write Response is lost when bonding has to happen first. ...
I'm trying to save power on my HID keyboard application by disconnecting the Bluetooth link after some time of inactivity. As soon as there are keystrokes to send, the device...
The question has been answered before, but the answer references a document called nAN-29 at this link: www.nordicsemi.com/.../73843444 . Which doesn't seem to be working...
Hello,
We use the PCA00031 dongle running the MEFW 0.9.0 in our production environment to validate a sensors accuracy. The PCA is controlled by a C# test program using...
Could someone explain the pin numbering scheme in regard to the interrupt setup handler?
To be specific, what pin number should be passed to nrf_drv_gpiote_in_init for...
In the ble_app_att_mtu_throughput example for the PCA10056 I am getting a "fatal error in the include chain" pointed from the #include "amt.h" line in amts.c. Specifically...
Hi,
I'm working on a firmware that is used in a nrf51822. I discovered an unwanted behavior of my system.
When the system is in power_manage mode, it can wake up in two...
● device : nRF52832
● sdk : 13.0.0
● softdevice : 4.0.2
Hi,
I have a problem with change mtu size.
I changed mtu size in sdk_config.h, but android application can't read...
Hi,
I am working on custom Board with nrf52382, I am using the mma8652 accelerometer for different functionality(prior is single and double tap detection).
Initially...
Hi,
Because of the compatibility issues I'm trying to use SDK10 for my nRF51422 device,
the problem is that I have flashed the S130 softdevice and the ble_app_uart, and...
