At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Long story short, I need to create a packed struct.
I knew the pragma way, to change aligment, didn't work.
I looked up and found the __packed (I'm using Keil µVision...
Hi,
I am planning two have the following network:
1 central communicating with 3 peripherals
One of the peripherals will be a smart device (iOS or Android). What...
Using SDK 12.2, I have compiled the secure bootloader successfully, tweaking the sdk_config and Makefile to use RTT for logging and turning on logging, and using the "_debug...
Configuration: Nordic PPK, PCA10040, PC10028 & PCA63511. Current consumption is relatively high on nRF52 vs nRF51; nRF51 is configured with SDK 10.0 and nRF52 with SDK 12...
Hi,
I have got my nRF52 DK. I could flash softdevice using nrfjprog.
But after reading s132 specification, i have following doubts.
How to flash application from the...
Hi all --
I have an application where I have a LDO generating 2.6V from a single lithium-ion cell. It has an EN input that I want to expose to the nRF52 with a little RC...
Hi,
I'm searching for the nRF52 Ref Manual. I've located the Product specification for the nRF52832, but can't seem to find anything for the Reference Manual.
I found...
To maintain compatibility with our current systems we would like to be force characteristics to be at certain handles, rather than having the soft device assign them sequentially...
I am upgrading from v12.0 to 12.2. I am using Linux, Eclipse, GNU ARM and Eclipse managed make.
I get compiler error ...nrfsdk12.2/components/drivers_nrf/hal/nrf_gpio.h...
Device: PTR5528
Board: custom.
I have just given coin battery directly to VDD. At P0.00, P0.02 i have two leds. On p0.03 and 05 i am having one interrupt and other is...
Hello everyone.
I am currently working on a device with some peripherals.
I have SPI slaves and other sensors that I am monitoring using GPIOTE driver.
I noticed a...
I am attempting to implement buttonless DFU with my application.
Using SDK v12.2.0 on a Rigado BMD-300 module (nRF52832)
Starting one step at a time, using nRFgo Studio...
I am running RTC in nrf51, after coming out of sleep mode RTC is getting reset.I want this RTC to keep running so that we can use it as wake up signal.
I am attempting to enable a second custom service with a vendor specific UUID with three characteristics (in addition to an existing custom service and the battery service...
