At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I'm new to use nordic and I would like to add a new custom service (2320EE58-8654-4132-95F7-0A872AC0958F) with a custom characteristic(23200000-8654-4132-95F7-0A872AC0958F...
Hi DevZone
I am trying to measure the battery voltage using the bas service. I got some hints from the ble_app_proximity example.
My problem is that no matter what the...
Please refer to the image below:(If you cannot see the image, link here: postimg.org/.../)
I'm not entirely sure what this pin does, does it output reference voltage...
Why can't I breakpoint or step blinky, using kiel MDK lite?
Comment --- I suggest Nordic do videos or provide exact steps for how to setup-run the base example (like Blinky...
I've been having a very difficult time debugging this issue. I've modified the bootloader_secure example and have it working on the dev kit using the 330 Softdevice. It works...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi Nordic,
My application does the following:
Timer 2 takes care of controlling a shift register (CLK and DATA)
Timer 1 takes care of polling data from sensor...
Hi!
I am in the process of upgrading a quite large project from SDK 8.1 to SDK 12.2. It uses the nRF52 DK, PCA10028. I still use the toolchain I stated with, including...
Following this tutorial , but for pca10028 , softdevice s130 instead. I'm on Linux.
Under "Running", when I press Ctrl + F5 , I get the error s130_nrf51_2.0.1_softdevice...
Hi,
I try to modifie ble_multilink example et send more than one data,
here is my main code code :
static uint8_t test[4] = {0x41, 0x42, 0x43, 0x44};
static...
Hello,
SPIS is adding a 350uA from 80uA baseline running current. I would like some tips and advise on improving this. Thanks!!!
The baseline operation consists of:...
I am using eclipse as IDE , but when i build ble_app_hrs example it's getting an error ../../../../../../components/ble/ble_advertising/ble_advertising.c:195: undefined reference...
I have a 32u4 Feather but don't get the right support from Adafruit to create my own Profile. I have downloaded Nordic's android app and can see all the characteristics on...
Hi.
I'm trying to enable and disable softdevice repeatedely.
In my code, softdevice is firstly enabled then advertising properly.
After some seconds, softdevice is disabled...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
