At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I am using SDK10 on nRF51422 with PCA10028. I want to port a code written from ant_sdm_tx_cadence_s210_pca10028 with s210 v.5.0.0. to S310 v.3.0.0 to include some BLE...
Hi,
Would anyone be able to upload a template code for programming an LCD using the nRF51822 or nRF51422 with SPI?
I am using Sharp’s LS013B4DN04 Memory LCD. Here's...
Hello ,
I'm Dinesh Katkar,We as team planning for wearable IoT product,so selected Nordic sem's Bluetooth Smart SoC for our end application.
Can we control the play...
I see that the IOS-Pods-DFU-Library interprets the value in this particular characteristic. But I could not find good documentation as to how should this be used?
Can it...
I am running arduino code based on "ble_uart_project_tempelate" in Teensy 3.2 for nRF8001 module. We want to introduce smart nRF52832 modules to rule out Teensy. Does nRF52832...
Hello,
This is in continuation of my previous question about the wrong UART speed. I got it working by starting the HF oscillator. However now the latest revision of our...
I am debugging UART routine and met an issue that it can return back to mainloop after UART receiving. Is there anybody who can give any advice?
Thanks in advance.
Alex...
I have one nRF52822 Ble. It has secure pairing mechanism.
when i connect iphone, App trigger Pair dialog from iOS. and press pairing, then stop.
i can follow nRF52822 code...
I've ported an nRF51 DK project over to the nRF52 DK and the only issue I seem to have with the nRF52 is that the device refuses to pair with my peripheral, hard faulting...
I used the nRF51822 for my thesis and as I was looking for the url of the product spec I used I noticed something strange:
My product specification for the nRF51822 is version...
I've connected my nRF51822 mKit to my Linux system via a USB cable. While trying to upload code on the board, I got the following error:
SEGGER J-Link Commander V5.12g...
Currently i was using arduino for my development but now i want to move forward with Some SOC so i found nrf51822 IC.For using nrf51822 ic i need to buy another board which...
I would like to use the nRF24L01+ for a telemetry project that requires broadcast at 100% duty cycle at a fixed bitrate. Ideally, we could also use our own frame format. ...
I am trying to use whitelisting and a passkey to add security for my application. So far I have the passkey set up so that it is working on the master control panel on PC...
Dear sir.
From [nRF51_Series_Reference_manual], ADC maximum input voltage has two rules.
The ADC should not be exposed to higher voltage than 2.4 V on an AIN pin...
