We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I'm trying to get a module with an NFR24L01+ on board to send a simple data transmission from a pic micro but after a couple of days of trying various combinations without...
i find that the macro APP_ERROR_CHECK call the macro APP_ERROR_HANDLER
do \
{ \
const uint32_t LOCAL_ERR_CODE = (ERR_CODE); \
if (LOCAL_ERR_CODE != NRF_SUCCESS) \...
HI all:
Because the application code is relatively small, bootloader is used dual_bank_mode, but now the application code becomes large, OTA can not upgrade, I would like...
My PCA10001 board is getting detected in nRFgo studio and i can even program it but its COM port is not getting detected in device manager.
I dont know what happened but...
Hello Nordic--
We're most of the way through qualification testing on an nrf51822 and the testing house had a question about the PIXIT values for RF-PHY testing. I sent...
Hi,
I find three different states that is related to DFU and app_button libary.
1, no DFU(that is no bootloader), but using app_button libary, there is no 0.9mA current...
Hi. I use the 'sdk 6' and 's110_nrf51822_7.1.0_softdevice'.
I would like to add security.
I tried to passkey. If i enter passkey, it is possible to bond. but It is not...
Hi all,
I can control volume up/down, music play/pause with the ble_hids module.
static uint8_t report_map_data[] =
{
0x05, 0x0c, // Usage Page (consumer device)
0x09...
Hi.
I'm currently trying to buffer data from beacon interrupt.
So, I choose to use circular buffer.
Before implementing it myself, I could find that there's already...
Hi
I'm using the Adafruit LE Breakout with an MSP430.
I made my own drivers in order to have full ISR support.
My setup works well (no error) i can connect/set_local_data...
Hi,
I’m currently trying to send strings about Nordic UART Service.
In use are two nRF52832 Develop boards. One as Central and one as Peripheral.
The connection works fine...
I have a PCA10040.
I downloaded nRF52_SDK_0.9.2_dbc28c9.zip.
I want to use "ble_peripheral\ble_app_uart " sample program.
However, supporting it is PCA10036. (by readme...
I am modifying the ble_central\ble_app_hrs_c example to connect to a peripheral with an "Authentication Characteristic" that is used to initiate the peripheral-specific authentication...
main.c: Warning: C3912W: Option 'device' is deprecated.
main.c: error: C3903U: Argument '-D__EVAL' not permitted for option 'device'.
i am getting error. can you help...
