Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
NCS3.0.0 , NRF52840
calling bt_conn_disconnect does not result in the disconnect callback being called.
the conn state seems to be stuck in BT_CONN_DISCONNECTING. I have...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
If I follow the Create New Board wizard it will only offer nRF54L15 from the 54L series SoC (I want 54L10)
The others are included in the SDK, and if for example I make...
The partition table for the nRF9151-DK is different than the partition table generated when the Create a new board option is used in the nRF Connect SDK and the nRF9151-LACA...
Hi,the Nordic team It only took me ten minutes to compile the whole Matter program yesterday morning, but now it takes me more than an hour to compile the whole Matter program...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
I am having issues getting the BMI270 sample working on an NRF54l15-DK, using nRF Connect SDK v3.0.2 and toolchain 3.0.2. After successfully building and flashing the program...
i would like to get MCC, MNC and other cellular data via API. I found lte_lc_conn_eval_params_get() function/API as part of <modem/lte_lc.h> that has the information I am...
We are using Thingy:91 X as an evaluation platform for our upcoming product. Our test application is made up of a nested-loop structure like
while(true){ lte_lc_connect...
I'm using the code below to trigger a callback on pin rising edge.
Unfortunately, the counter is not being increased at all. Any reason why? I used multiple sources already...
Hello Team,
I AM USING NRF52833QDAA IN NRF CONNECT SDK , IN DATASHEET P1.09 IS MENTION BUT IN OVERLAY FILE OF NRF52833QDAA AT ALIASES PIN P1.09 IS NOT MENTION OR NOT DEFINE...
Setup NRF52840 with SDK 17.1
FreeRTOS tickless idle mode
When we call xTaskNotifyWait and then get the notification then function returns but the result of the function...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
