Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
I build project without problems, but this simple sample return zero results for read buffer. I return 5 zero from 5 zeros. I have right names for overlays files. nrf9160_pca10090ns...
I'd previously run into this problem with mqtt_publish not being able to handle large payloads, larger than approximately 2k.
At the time, the suggested workaround was to...
Hi All,
I am working on a project where i need to communicate using i2c protocol. For this i need to set i2c frequency 20 Khz. So how can i calculate register value to set...
software : nRF5_SDK_14.0.0_3bcc1f7
hardware :nrf52832qfaa
example : ble_app_hrs_rscs_relay
i want use "example : ble_app_hrs_rscs_relay" to receive more then 20 byte...
Hi all,
I have a DK 10056 rev 1.0.0, and it suddenly stopped working on the Embed side. Using the USB port (the DK one, not the NRF one), the LEDs (4 LEDs for testing purposes...
Hi,
I am using an nRF52 based chipset and programming the device with the hex file.This is being performed using the nRFConnect v.3.4.1 Programmer. The erase and write option...
Hi,
I have a custom prototype board based on nRF52833 which runs a working firmware and I have not any other prototype ready to hand.
Unfortunately, I think that the source...
Hello,
Considering the waveforms in the following chart, which will be the best approach to keep the power consumption as low as possible?
Specifically, which peripheral...
Best regards:
I have one PTX and one PRX, both nRF24L01+ with PA and LNA. PTX send 4 bytes to PRX but PRX doesn't get RX_DR, and PTX fire MAX_RT.
PRX:
PTX:
...
Hi
I had a strange error when I Set up a project in Segger, I got TRUSTED EXECUTION NONSECURE error.
I was trying to build the project for thingy:91 with nrf Connect SDK...
Good day;
I read the relevant posts. But I'm confused and do not understand.
1. What is the best way to identify the requesting device? Its specification identify is unique...
Hello
I want to set up the SEGGER Embedded Embedded Studio and I'm at the stage where I should select the board directory.
The Getting started Assistant shows an example...
Hi
in nRF9160, there are several AT commands to measure/handle battery voltage: examples:
%XVBAT
%XVBATLVL
Which PIN do they sense? are they VDD1 & VDD2 (which I believe...
Hi,
I am currently developing a health monitoring device. I would like to know if the nRF9160 is certified to be used with the LTE network in Canada. I am interested more...
