We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I am currently following the tutorial for creating custom services ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ). The only differences to this...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project. I need to work with another chip through SPI. This chip is the master and...
Hello,
I have one more questions while doing test with SAADC, UART.
When I was tested the SAADC pin connect with ground, the negative value occurs.
So, I changed the...
Hello,
i've built a basic Thread network with two nRF52840 Nodes running the CLI example and a RasPi with a nRF52840 RCP as BorderRouter.
My Question is:
Whats the...
Hi.
Hope you are well.
I want to send data from nRF51822 to nRF24L01+. I used the esb library to configure the nRF51 and I just change the settings as I want ( some settings...
Hello~ I have previously written related articles. But I don't get the answer I want, so I ask you again. Use the toolchain manager to use ncs 1.3.1. The error as shown in...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello guys!
We are workng with nRF52840 SoC and SDK v17.0.2.
Custom BLE Services and Characteristics are needed to implement in our device. Before starting that implementation...
Hi,
In our design, nRF9160 is powered by a LiPo battery, making VDD = 4.2V in a "fully charged" case, and VDD=5V in a "lipo is charging" case.
We would like to be able...
In trying to use a private key file to sign the application image I'm running into an issue with the PEM file. I created a PEM file using the following command:
as documented...
Hello colleagues,
Mi name is Daniel and i'm trying to develop a software application that let me calculate the PER (packet error rate) of a bluetooth transmission.
The...
Hello Team,
I am working on a project in which I want to used pdm microphone with nrf51822 xxAA and i am using keil u5.
1) So I have picked uart over BLE example from...
Hey there,
I am new to the community and I would like to looking for more than one cell. As I readed in another thread, it was possible with %NBRGRSRP a few month ago. ...
I was looking through documentation and I noticed that in OPS v0.7.1 the cold start was stated to be -144dBm. In PS v1.1 it calls out -142dBm. Can you explain why they are...
