Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi all!
Resoldering usual QFN packages with pins along the edges is not such a big problem... but how is this usually done with devices they have pins underneath the package...
Configuration: 52840 / S140 / V610, SDK 15.2
As approaching production, I am continuously testing S140 on various environments.
I noticed during testing that there are...
I got Thingy:91 and want to install at_client to it, but it doesn't work well.
What I did is
1. Check out a pull request and update firmware referring to this link ...
Hi everybody,
I work on custom board with the SDK 15.2.0 and the SoftDevice S140.
I work on the ble_sdk_app_template example. I tested it on the nrf52840 DK and it work...
Hi,
I am a beginner in nrf52840 DK. I am trying to run TCP example. I have flashed client example in the DK and able to connect to the laptop(LED_2 ON). When I press BUTTON_1...
Hi There,
This is Particle's Sr. Hardware Engineer, Ping. We are working on a SoM (System-on-a-module) called EG91-SoM that with a nRF52840 (Thread) + EG91 module for acting...
Hello,
Hardware: NRF52840, Development Software: any
I am hoping to generate 3, or ideally 4 separate (independent duty cycles) PWM signals at a frequency of at least...
I use sdk13.0,s332,when my system working,it will auto reset about 129 seconds per time,I make a breakpoint,find it caused by "softdevice_fault_handler",when it reset,the...
Hello,
I am starting development on what should be a straightforward application using the nRF52832. It is actually this BLE module , which contains the nRF52832. However...
I am wondering if I could have access to a mechanical drawing or 3D model of the N RF52840-DK . Does anyone know where I could find either of these?
Thanks,
Julia
I am trying to understand why my program is returning this error (NRF_ERROR_RESOURCES). I read through a lot of other posts in the devzone and tried replicating them, but...
My board is nRF52840 + S140 + nRF5_SDK_15.2.0_9412b96, my configue as below picture and file "ywk_bsp_ble.c" .
When nRF Connect APP connect my device, it alway be disconnected...
Hello,
I am using nRF52832 (BT832 module designed by fanstel) based module for my application. we have developed customized PCB using the module. while evaluating the...
What chip supports Open Thread? SDK and softdevice versions supported?
We are in evaluation phase looking for potential radio manufacturers for an upcoming project.
Any...
