Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I'm working on the product using the nRF51422 QFAAE00 , SD110_nrf51_8.0.0, SDK 10.0.0. My product has the advertising flow as below
The device advertises forever...
Hello!
I have a problem when scanning and advertising at the same time with a NRF51822 and S130 v.2.0.0. (SDK11).
I can start both scanning and advertising without any...
Hello,
I am designing a PCB layout using nRF52832, I want to make it as small as possible so I am considering to route all component tracks to another layer.
I want...
Hi,
For an application I have a nRF51 at my disposal and I need to transfer about 3'000Bytes. I found in the documentation that the nRF51 can use the S130 SoftDevice which...
Hi.
Using PCApp/MCP(v 3.10.0.14), How can "BLE_GAP_EVT_SEC_INFO_REQUEST" occur?
Or will not it occur?
If it occurs, please tell me how to do it.
Thank.
Hello,
I need help about the multirole with the Freertos.
When I take the code example from Nordic "C:\Nordic\nRF5_SDK_13.0.0_04a0bfd\examples\ble_central_and_peripheral...
Example project: blinky_FreeRTOS_pca10028.uvprojx
I include SEGGER_RTT.h file.
After execute vTaskStartScheduler() function.
SEGGER_RTT_printf(0, "Hello World from SEGGER...
Using C11 compiler, and a Makefile from a template, where the Makefile defines CFLAGS with -Werror I get:
.../components/libraries/util/app_error.c:47:5: error: narrowing...
I running the (nrf52) HRM profile with FreeRTOs and connecting the BLE device with the Nordic Toolkit app.
On occasion the connection to the BLE device fails. After repeated...
Hi, I want to interface BLE module with freeRTOS. Does nordic provide BLE stack for freeRTOS? and if yes then is it opensource? or is there any standard BLE stack which can...
Hello,
I want to design PCB antenna for nRF52832 chip. I took reference from nRF51 dongle hardware layout.
I wanted to spread antenna upto 18mm width so I reduced the...
Hi
The j-link detects the chip, but for not obvious reason the j-link and keil will trough an error when I want to program the chip, here is the j-link out put. do you have...
Dear All,
I would like to order Li-Po batteries for my nRF52840 development kits and need some information. From the battery, what type of female battery connector is needed...
Hi, I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
