This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
We have a custom PCB that includes an nRF9160 and nRF7000. We’re planning a hardware update to add external flash memory and would like to know if we can use the...
I'm currently working on a matter application on a custom board in NCS 2.9.0. In the documentation for the ipc_radio net core image the README at nrf/applications/ipc_radio...
Hi all,
I am trying to configure the NFC Pins for usage in an SPI application. However they do not even work for a simple nrf_gpio_pin_set after configuring them with nrf_gpio_cfg_output...
Hi
I have developed a PCB that will be used to control some sensors. The pins NFC1 and NFC2 are intended to be used as GPIOs. However, the default processor settings configure...
Are there any ways/workarounds/configurations to drive P0.9 on nrf52840 as an Input/Output instead of just being NFC pin.
Technically we should be able to drive this pin...
Hi,
I'm using an ISP2053 (nrf5340) chip on a custom board and debugging using the nrf5340dk. I'd like to use P0.02, P0.03 as part of an SPI bus.
I set up a simple experiment...
Hello everyone,
I've recently migrated a code from nRF51822 to nRF52832, thus I started using fds library to manage flash storage from SDK v17.1.
The issue I'm having...
So i have a custom nrf52840 board that i'm working on with SDK 15.2
I want to use the NFC as GPIO.
According to the docs i need to set in the sdk_config.h CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I'm developing an Android app that will be used on Samsung Galaxy Tab devices only in which the user can connect, through BLE, to another device, which is a module added...
Hi
We have a product that uses a nRF5x Soc. Is acts as both a central and peripheral. The central part connects to a pulseoxymeter, and the peripheral part allows an app...
Dear Developers,
I am in the process of implementing the nRF9151 and would like to inquire about the necessity of the blind vias in its pad. Like on the nRF9151-DK.
Are...
SDK: nRF Connect SDK 2.9.0 with VS Code
SoC: nRF52840. nRF52840-DK for development.
We are currently using USB to output logs for debugging. For production, we disable...
Hello, I am following the official tutorial ( academy.nordicsemi.com/.../) to enable DFU over USB function on both nrf5340DK and thingy53. I am using sysbuild for both board...
Hello Nordic Team,
I am working on measuring battery voltage ( 3.7V ) using a voltage divider ( 220KΩ and 100KΩ ) connected to AIN2 on the nRF54L15 DK.
However, I am experiencing...
My device is a peripheral and during bad RF conditions I would sometimes see a BLE_GAP_EVT_CONNECTED event but the central never receives a packet from the peripheral so it...
