After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Hi,
I need to implement, say, 100 LPN + proxy and 1 friend + proxy, LPN are measuring devices.
1) How can I request from each, let's say, a temperature value? I want to...
There are two boards, Raspberry PI4 and nRF52840-DK . The task is for the nRF52840-DK on zephyr hci-uart firmware :
https://developer.nordicsemi.com/nRF_Connect_SDK/doc...
Dear Sir,
I use the nRf52840 DK (PCA10056) which be a ICE to download FW and 3V DC power supply for my DUT.
the 3Vdc connect to Vdd.
I use the DK 3Vdc be my power supply...
Hello,
Here is some information from my environment :
nRF9160 DK
SIM iBASIS
Country: Suisse
Operator: Swissom AG
roaming mode
Use LTE Link Monitor
I...
Hi,
I want to use tne NRFX SPIM module for reading and writing an external spi flash (at25df011) .
I looked at the example in order to reuse it or base my application...
Hi all,
I'm working on a project in SDK 5 (V17.0.2) on a custom board using a raytac nrf52840 module. IDE is segger embedded studio with a J-Link interface to the hardware...
The device we are using is nRF51822. It uses a bootloader from the Nordic SDK 11.0.0
The boot-loader we are using for the nRF51822 has several blocks of code in the SystemInit...
Hello,
I'd like to enable an instance of SPIM2 master (base address: 40023000) in SDK 17.0.2 for SPI operations. In sdk_config.h, there are two options, NRFX_SPIM2_ENABLED...
I am trying to run the heart_rate_collector.py example in Nordic's pc_ble_driver_py library. When I try to execute the program, I get the following error:
Command used...
Hi!
I'm trying to do the TCP example with the nRF5_SDK_16.0.0_98a08e2, a nrf52840 DK board and a Raspberry Pi 3 B+ as a gateway but I got some problems.
For connecting...
Hi, I'm testing the ICMP example, using a Raspberry and a custom board with a nRF52840. I follow the instructions on the "Connecting devices to the router" found in the infocenter...
hello,
i am using two customised nrf52840 boards and this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo to get the maximum range between two boards...
Hi.
I have NRF52840 with softdevice and GPIO0.7 and 0.27 connected to DALI CLICK and set up and 0.7 - IN, 0.27 OUT. I'm also using TIMER2 for running callback every 104us...
I'm using nRF52832 with an external motion co-processor. As a part of a robust reset strategy, I want to connect a single nRF52 pin to the co-processor's nRST pin to generate...
