This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I was trying to connect my cellphone tu the ublox modulo for sends at commands from my cell, in the main program of the micro I've the next lines for turn on the ublox module...
i have a nrf52840 dk
i need to connect the flex sensor to the board and know the resistance value while bending
how to do it?
and what code should i dump
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
I can't install the tool chain.
Looks like I have to install something called chocolatey?
I can't install chocolatey. I tried the chocolatey website for help and was baffelled...
Hi, I am trying to debug the blinky project with Eclipse, openocd and st-link. No softdevice. This is the output I am using.
I am finally able to see the leds blinking in...
I am studying to use the nRF2460 or wireless digital audio streaming where one Tx broadcasts and several receivers listen and follow. I have the following questions: Can an...
Hi,
How can I read out a vendor model in the NRFMesh app? When I change the model ID to e.g 0x9000, I cannot see the model under elements anymore. Needs there to be any...
I have a list of characters and trying to put them in a string.
char line[13]; /* Line buffer */
NRF_LOG_INFO("Playlist : %c", line[0]); this works displaying 1 character...
We are currently evaluating the two development kits of nrf91 - On the nordic Thingy with Fractus antenna we get the nrf91 into the mobile network after about 20 seconds ...
I know this may be a duplicate of this: https://devzone.nordicsemi.com/f/nordic-q-a/37732/nrf52840-spi-clock-line-contention-causing-spi-driver-to-hang/145521#145521
I say...
Hi,
My working environment:
NCS folder Tag:v1.2.0
J-Link version : v6.62a
SES version:4.42a
test sample code:\NCS\nrf\samples\nrf9160\cloud_client
nrf connect...
I generated two packages for OTA. The first package contains a bootloader and a softdevice 7.3.0. The second one contains a bootloader and a softdevice 8.0.0. I flash the...
Hello,
I want to interface nRF9160dk with ICM20648 sensor using SPI communication protocol. I tested SPI on nRF91 and it is working fine. But how to use ICM20648 with nRF91...
[Embedded World 2020] Failed update of the Thingy 91 Certificate after downloading from the nrf cloud
I Just tried to update the certificate from the NRF Cloud ( https...
https://github.com/NordicPlayground/nrf5-calendar-example
What is lowest power mode where real time clock could run?
How could retain RTC value during reset?
Thanks
