Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
I am using nRF51, SD 130 1.0 and SDK 10.0.0. I have 11 buttons connected to nRF. Currently it only works for up to 4 buttons (APP_TIMER_OP_QUEUE_SIZE is 4, but I'm not sure...
Hi,
i am working on spi master example in nrf52832, when clock is set to 8MHz, clk signal output at the nrf52 pin is more like triangle wave.
is there any way to set pin...
Hi,
At the moment, my current location does not have an NB-IoT network for the nRF9160 DK to attach to. This means that the device is unable to activate PSM mode (which...
Working with SDK 15 on an nRF52832:
I have a peripheral applicatin where I'm computing the value of a BLE read on the fly.
Currently I do that by:
Setting up a BLE...
Dear dev community,
I've got a very simple question: How can I see the subscription and publishing addresses list in any mesh node for any model?
Thank you!
Regards...
Hi I am developing a custom PCB for the nrf51822 chip. I heard the nrf51822 chips do not come with preloaded firmware or bootloader. Do I need to also flash the bootloader...
Base on nRF5_SDK_15.3.0_59ac345 for NRF52810, I wrote the following codes,
Use nrf_drv_uart_tx to send data is successful, and NRF_DRV_UART_EVT_TX_DONE occur normally...
Hi All,
I am interested in designing my own Bluetooth beacon (Several of them, about 10) and connect it to a computer and read sensor data from those beacons (For example...
Dear Nordic:
Hi,i install nRF Studio <nrfgostudio_win-64_1.21.2_installer.msi>, and i want to erase NRF52840 flash,but when i click on "nRF5x_Programming",i cannot get...
Hi guys! I feel really excited about working with Nordic Semiconductors, but I have a problem with PWM driver.
Do you know how to support 13 independent devices that will...
Hello,
I was looking into the nRF5280 and was going to purchase it. But I had some questions that were not cleared up in the data sheets. It seems that a battery or a power...
Hello Everyone,
I have been using nrf52840 DK for several weeks. However I find it very difficult to understand the source code. I have experience only using arduino programming...
I've been attempting to use PSM but got an error.
I've already checked the post below. I download the project file and fixed a bit.
https://devzone.nordicsemi.com/nordic...
Hello .
I am looking for a way to pass the calendar time from the PC by the emulator to the MCU on first run.
I am using Segger Embedded studio 4.12
Is there a function...
I get the following error when launching the app, and the "Start scan" button either doesn't do anything or can't be clicked.
Error while probing devices: Error occured...
