This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I’m currently trying to design my own pcb based on nRF52 Development Board. I went through a number of pcb files and all of them are associated withnrf52832 without...
i use the keyboard project, bond and pair the iphone7(ios11.2), the iphone display is connected,ok, then i reset the keyboard and erase bonds, the iphone display disconnected...
Hi Dev Zone,
I am attempting to flash a blink led app, based on Zephyr (nrf52_pca10040), to the primo core (contains Nrf52832), through Jlink debugger on a Linux machine...
At what voltage should DCDC be manually turned off for a nRF52832 ?
This thread for nRF51 says:
You must manually disable the DCDC when supply voltage goes below...
Hello,
I followed the steps mentionned in this blog
I did all the required step but I'm still seeing the same behavior.
below is my setup :
I'm using nRF52840 and...
Hi folks,
We got a weird behaviour with our nrf51822(SDK 12.2.0, s130) device. we have built a low power application with following parameters:
MIN_CONN_INTERVAL...
I have tried to understand how data was send from two BLE device. I have had 2 PCA10056 board and I have loaded ble_app_blinky example and ble_app_blinky_c example for each...
Hi All.
I have one question.
I just want to send "volume down key" simplely after connect with android device to take a picture.
I have no idea. and I don't understand...
I modify nrf51 nus in SDK12.3.0 to realize my application, I found when enable uart, the consumption near 830uA , and then call app_uart_close(), the consumption near 5uA;...
Hi,
Is there and C/C++ source code to get float value from 32-bit ieee-11073 FLOAT data type
I need c/c++ code to parse 32-bit ieee-11073 FLOAT data coming from FORA...
Hello,
Using Spi bus with frequency = 4Mbps give me this deformed signals (clock and miso) and when I push it to 8 Mbps I am not able to get the correct values.
Obviously...
When an event is bound to the ppi channel, and this channel is bound to both task_capture and task_clear
can I get the correct COUNT value when an event occurs?
Or can...
Hi all,
I wanna build a IOT gateway. I follow this steps infocenter.nordicsemi.com/index.jsp
When I access coap://[ipv6] It dont have resource light, just only have...
[SDK 12.3.0 / nrf52 DK / Keil tool / beacon example code]
Hello. i am a novice developer.
Power On - Beacon data transmit and enter to sleep mode after 10 sec
...
I fail to integrate “ble_app_multilink_central” and the uart portion of “ble_app_uart_c”
I have checked other posts and it is inconclusive if and how they got the integration...
