Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
I have a similar question as posted here but I wonder if this limitation is still the case.
I am trying to advertise to a specific device by passing the scanner device's...
Hello all,
I´m Trying to Run the Minimal-Example of Sensor-Stream API
https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/sensor/stream_drdy#id7
HW is:...
Hi All,
I have a ordred couple of 5340 Audio DKs. I want to configure one of them as headset using the nrf_audio example application and connect to a phone and stream...
I'm developing code to run on the nRF5340 SoC in a Thingy:91 X and I am seeing duplicate RTT output. For example, if I look at the RTT output from the default 'Connectivity...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I saw a really similar post but no real solution. I've got both a nrf52840dk and a fanstel ble840xe eval board that I've been playing with. the end goal is to make this start...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Regarding...
Hi everyone,
I'm new to Nordic development and currently working with a custom board based on the BC40C module (using an nRF5340). I’m facing an issue with the Bluetooth...
I’m working with nRF9151 + Toolchain 2.9.0 and wanted to share my experience & issue while sending ~7kB data over UART. I’ve tried both DMA & FIFO-based approaches — here...
I am designing a wireless sensor pcb with the nRF52840. I am essentially following the Circuit configuration no. 4 schematic for QIAA aQFN73 from the datasheet to a tee (schematic...
Hello,
I have bought a couple of Nordic NRF54L15 DKs, and it seems that the distance measurement toolbox that was compatible with the NRF52 series is not supported in...
