Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello.
There is nRF52840 and nRF9160 on nRF9160 DK.
here are codes on this two chips:
nRF52840: 1:SoftDevice. 2: BLE APP
nRF9160: 1: Modem & GPS firmware. 2: Bootloader...
Looking at PM_EVT_CONN_SEC_FAILED parameters, i.e.,
re: nRF5 SDK v16.0.0, nRF58233, S113
Looking at the definition for pm_sec_error_code_t: “Possible values are defined...
Hi All,
I've had a product (RunScribe) in the market for some time, running on the nRF52832. This was built on the SDK13.1 / and the S332 v4.0.2 SD. All using Keil. As I...
Hello!
I'm planning to start a project with the nrf52832 chip, I mainly choose this product, because of the low power consumptions and ble.
I would like to start my development...
Hi I am using ncs version 1.5.0 and dk version 1.0.0
I just want to try a simple ping test.Is there any at command are sample code is available to check the network connection...
hello i am using nrf52840 with our customised board with sdk version 15.2 i am trying to achieve maximum distance using coded phy with nrf long range demo as my base i have...
Hello. I tried to run ble_peripheral/ble_app_uart example from the newest SDK (17.2) on my ebyte e73 with nRF52833 onboard, but without success. I used softdevice S140 (tried...
HI,
My application needs to send the data from PC(server) to Nrf52840(client) . The length and type of the data are 2758 bytes and char data type, actually data has been...
Hello !
I allow me to contact to you because I don't go through a building issue.
I'm using SEGGER Embedded studio for ARM V5.40c. My target is N52832. It is not the...
Hi,
I'm working on a nRF52832 project with adc and ble function involved. An external RTC is also included, communicating with MCU via I2C. Everything goes well until I...
Please help to tell the meaning of the "built code" after the NRF51822-QFAA-R7y
There is mention "(H0) of built code. Is there any functional / firmware / hardware difference...
I'm using the latest SDK (1.5.0) on a Windows 10 platform.
I want to add I2C support to the BLE sample program peripheral_uart.
I fumbled my way through https://devzone...
I'm using sdk 15.3.0 and s132. Is there an API that I can query the bluetooth connection status? What method can I use to find out if a connection is currently available or...
