Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
sir/madam i am beginner in nrf52 i want to display time stamp using an in built rtc. i am using that nrf calender in github as reference i am getting the following 4 errore...
Hi,
I have a problem with resume suspended TWIM transmission. My goal is to send | START | ADDR | DATA 1 | DATA 2 | STOP | where DATA 1 and DATA 2 will be send in two separate...
Hello
I am using SDK v17 and nRF52DK board (PCA10040) and testing mpu6050 sensor.
I want to print out the sensor value through the app through ble_app_uart.
Before sending...
HI.
I am trying to connect a laptop BLE and a custom device using HID.
I have to connect multiple devices to my laptop.
I know that the maximum number of connections...
There is an error in projects that utilise RTT for CLI. SDK_CONFIG.H contains the line CLI_RTT_ENABLE. This must be CLI_RTT_ENABLED for the macro NRF_MODULE_ENABLED(CLI_RTT...
I go into MCUBoot mode and I get: MCUboot DFU failed. Error occured when program. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: Unknown value (ffffff8e) When trying...
Hi all,
I'm evaluating design for a bluetooth + GPS + NB-IoT ultra-low power device
I see the only possibility to get a such module is to design it (I didn't found anything...
Hello,
I'm trying to auto-build my application through Github actions however I'm running into this problem
When I try to run this locally it works perfectly fine however...
Dear All, I am trying to measure the current consumption for an application I am developing on the nRF52833 DK. The code that I am running is the following: Based on the product...
Dear All, I would like to configure a device to go to the System ON, no RAM retention, wake on RTC (running from LFRC clock) Sleep mode, in order to be able to use the RTC...
Hello,
we are using nrf5 SDK version is 17.0.2 and nrf52840.
Our product uses nrf52840 and its USB capabilities being configured as a composite device (HID keyboard +...
Hi,
i would like to know which software i have to download and install, so that i can program a really basic function like pressing the button and turning on and off an...
Hi,
I saw a Linkedin post by Zephyr where they mentioned some Vscode extensions for devicetree and kconfig:
https://marketplace.visualstudio.com/items?itemName=trond...
Hi,
unfortunatally i could not add a new LTE device. I was able to activate my SIM card but not able to finally add the device to my account.
The error code is: There...
