This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
We are using SDK 2.4.0 and have enabled MCUBoot to support OTA updates using the dual slot method. I have reviewed many posts and existing tickets and have not been able to...
hello everyone,
I am using the nRF52840-QFAA-R7 (48-pin package) along with the nRF52840-DK development board. I have a question regarding I²C communication. Currently,...
Hello everyone, I am planning to make a wireless keyboard, and one of the requirements is that it has a long battery life, so I am very concerned about the power consumption...
So I've been playing around with some code example to make UART work (which I did eventually) using NRF SDK 5 (v17). However the last version of SES (8.22a) requires some...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
Hi,
I'm working on an nRF5340 + nRF7002 project using Zephyr RTOS , where the device enters low-power sleep and wakes up on a hardware counter alarm ( counter_set_channel_alarm...
I had been doing this:
What it does:
create a CHG (channel group)
DPPI is triggered by a GPIOTE in-event
DPPI then triggers and EGU, a TIMER capture, and...
DPPI...
Hi
board: nrf52832 DK
sdk: nrf connect sdk v2.6.1
I have successfully integrated the provisioner and light switch client together. Now I can control the light switch...
Good morning,
I would like to know if it is a good idea to store serial number on UICR register when using nRF9160 at production stage.
If using UICR, which register should...
I have compiled the sample code from ncs/v2.9.1/zephyr/samples/drivers/uart/echo_bot and loaded it onto an nRF54L15 dev kit.
The dev kit is connected to my pc running a...
Dear forum, I am trying to implement some examples from the nrf5340 Product Specification but the register names does not match with the ones in the include files. I am using...
I am trying to run the USBD_BLE_UART for nRF52840 on a PCA10056 board.
I installed the USB driver that comes with the SDK (17.1.0).
My computer is running Windows 11....
https://openthread.google.cn/codelabs/openthread-border-router#2
following this webpage to setut rcp board router(by flashing coprocessor app to nrf52480) and flash the...
Good morning,
I have created a python script which allows me to flash modem firmware at production stage.
I'm using modem firmware mfw_nrf9160_1.3.6.zip
I'm using pynrfjprog...
