Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I am trying to migrate my project developed on Mesh SDK V2.0.1 to V3.1.0. I followed all the steps you recommend but i am stuck with the configuration of my server node...
hi all ,
i run Serialization application between nRF52840-DK ,it not start up.
how to Debugging this issue? i have been reset connectivity board,the error message halt...
I am trying to connect the MS5611 ( https://www.te.com/usa-en/product-CAT-BLPS0036.html ) using the GY-63 Sensor Module to the n RF52840 with the nRF5_SDK_15.3.0_59ac345 SDK...
Hello.
I would like to know which PCB surface finish would be used for bluetooth application. There are HASL, OSP and ENIG. nRF51822 IC chip and PCB trace antenna will...
Hello All,
We are designing a Tracking device system, for this we use nRF9160 LTE+GPS combo module. this system is battery operated so we need to monitor the battery continuously...
Hi,
I've been trying to lower the power consumption of the MQTT example and followed the guide in here .
1. I compiled the low power UDP example and do exactly all the...
My nRF52832 firmware application transmits data to iPad which converts it into a flowing waveform. The waveform flowed smoothly when SDK13.1 was used. I migrated the firmware...
Hi. I use 15.3.0 SDK and Segger studio.
I test Ant communication
I have a question.
ant_bsc_rx example of Ant plus, there are 2 handler.
ant_bsc_evt_handler is set...
Hi guys,
I’ve got a simple nrf51822 board which does not have any GPIO used - the system is a beacon doing its own advertisement without any intervention. The board schematic...
I am getting started with the NRF51 DK. A previous post suggested that " you should start with the precompiled versions of the examples that include the SD. These always work...
Hi.
I'm useing SDK 15.3 for testing DFU in nRF52832. I've already porting DFU to project ble_app_uart_c. now, I want to run BOOT project,and I'm useing project secure_bootloader...
Hi,
I understand there have been a few changes in the nRF Connect SDK with regards to Secure Boot and SPM.
I've been stuck for many hours trying to understand why I'm...
Hello,
I'm facing an issue when i want to delete some file in my FDS file system. Indeed, sometime, i can find dupplicated file with the same file id and the same record...
hi ,
i just realized that i damaged my NRF52 dev kit debugger chip. it is heating up and not working . the rest of the circuit including NRF52832 are fine. is there any...
I am using sparkfun nrf52832 breakout. I am new to this. I don't have a JTAG programmer so I cant program with keil. Is there an alternative solution for the software used...
