I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Using SCAN_INTERVAL and SCAN_WINDOW at 1600 vill make the flash write and erase come out with a error, the fstorage is working fine before the SD is initialised.
/** @brief...
Hi,
I am using the secure bootloader as a template and I want to use the inactivity timeout to shutdown after 10 minutes.
I saw that the limit should be 60000000 ms (according...
SDK: nRF5 SDK for Thread and Zigbee 1.0.0
I have code for the SAADC based on the Low Power SAADC example here .
I have modified it to sample 4 inputs, and changed the...
Hi,
I would like to check battery level using the SAADC of the nrf52840.
Assuming the voltage is less than 3.6V, do I need to have a resistor between the battery and the...
HI,
I am new to IoS development with NRF.
I am having NRF52840 DK, IoS device. I want to implement USB HID device application (similar to pulse/Gluco meter ) on IOS. I...
Hi,
I am not able to compile the SDK example by using SES for ARM V3.52.
I got one error which shown below:
It pointed to the link ldr r0, =%4
Thanks
Gan
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a.
I am writing a program with keil.
I am currently doing SPI communication with BLENanov2(nRF52832) and SD card with...
Hi,
I am implementing the UART on NRF52840. TX works but the RX doesnot. While debugging, I noticed that STARTRX task register is not getting set due to which the RXDRDY...
Hi Sir
We'd want to do RX testing with DTM mode, however, the dtm example code looks can't report receive data or total packets counts,
So that, we don't know how to determine...
Hello,
I'm using the nrf15822 chip and am using the ble_app_uart example from nrf5_sdk_12.2.0.
I know softdevice will automatically generate random numbers through RNG...
I've been told due to PAN 58 it is not possible to use EASY DMA with nrf52832 without switching to the deprecated SPI driver. Is there a workaround that allows the use of...
Hello,
We are going start custom PCB design by using nRF52840 chip and SDK 15.0, but confused for use 3rd party nRF52840 modules or design complete custom PCB using componenets...
Hi,
Despite knowing a fair bit of the theory of wireless comms (mainly PHY and MAC), I'm brand new to actual hardware configuration/protocol development, so please be gentle...
As a master device with a whitelist there is a limitation on how many slave devices can be connected. If i am correct, other than whitelist there is no restriction to the...
