Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello everybody !
My code is based on the code of the "ble_app_template" to which I added my own custom service composed of 4 characteristics sending notifications. Notifications...
Hello Nordic developer, I'm asking my self if it's possible to use a task of one timer like STOP TASK or START TASK as PPI event ? For example, like that :
I expect that...
how can i program in nRF 52840 UARTE. i want to communicate with other serial device using nRF 52840 UARTE communication (send and receive data).
can you send me the snippet...
Hi,
I am developing an ANT+ embedded device (nrf52832, SDK14.2) , that (among other things) acts as a BSC receiver. I have a BCS sensor that is seen in Garmin Edge as 136150...
I want to transfer data using UART to BLE by Baud Rate 19200(using nRF51822).
Transfer data speed need to achieve 2KB/sec up.
How can I do it successly?
Thank you...
I noticed that you have a branch called feature/v6-upgrade for pc-ble-driver. Is that branch usable for 52840 and s140?
By usable, I mean it can be mostly usable and we...
Hello,
I am following the PPK Get started get started of the PPK board.
I am developing on the NRF52-DK (Rev 1.1.0 2017.23) - nrf52832 My SDK is the nRF5_SDK_15.0.0_a53641a...
Hello everybody,
I am using sdk14.2, s132 with Nrf52832. I want to define the pin of the NRF52 as the input and decode the incoming pwm signal. For example, I have a signal...
Hello,
I am working with the BL652 EVK from LAIRD. The EVK has nRF52832 IC inside of the module. I downloaded the " nRF5_SDK_15.0.0_a53641a" and trying to use "ble_app_uart_pca10040_s132...
Hi. I am trying to develop an multiprotocol test example using SDK 15 and nRF-IEEE-802.15.4-radio-driver on NRF52840 dk board. I need that BLE and 802.15.4 stuff can work...
I have a confusion about mac address of nrf51822, I run example ble_app_uart .
When I use nRF Connect on Android, I can see the mac address of nRF51822 is CB:16:04:4A:10...
Hi,
I use nrf52832QFAA, SDK 11.0.0, Softdevice 132 v2.0.0. I need to add a device_manager_central to my project (in my project it's easier and faster than adding a peer_manager...
Hello,
In the documentation for nrf_serial_write function (SDK 14.0.0) it is written:
timeout_ms Operation timeout, in milliseconds. Pass 0 to operate in non blocking...
