But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
The comparator (COMP) in nRF52 can use three internal reference voltages (1.2, 1.8 and 2.4V). Is it possible to also output these voltages on IOs?
Best regards
...
hello there in my code,
APP_ADV_INTERVAL 64
APP_ADV_TIMEOUT_IN_SECONDS 5
using nrfsniffer i am getting 57 packets in 1 second.
i can't understand it. because APP_ADV_INTERVAL...
Hi!
I tried to some research in the forum but I would like you to assert my final decision.
My goal is to design a sensors network (at the beginning with five end-nodes...
I am working with some code from a previous provider and I found in its void bsp_event_handler(bsp_event_t event) function this code:
case BSP_EVENT_MID_PRESS:
err_code...
Not sure if this is the proper venue for a bug report:
In nrf_nvmc.h (from SDK v12.2.0)
/**
* @brief Write consecutive words to flash.
*
* @param address Address...
Hi,
We need to add WeChat / AirSync functionality to our nRF52-based product. Is there any support available from Nordic for this kind of environment? For example ble_wechat_service...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
hi，
i can't find the ID for softdevice_s140
run cmd ： nrfutil pkg generate –help
--sd-req TEXT The SoftDevice requirements. A comma-
separated list of SoftDevice...
Hello,
I´ve got a problem with the primary services discovery when register more than 1 vendor specific UUID.
I´m actually connecting one Cadence Sensor and one Motion...
Hello!
I have problem with DFU bootloader on nRF51822-xxAA.
For first, I made all steps for upload bootloader(erase chip, upload SD s130, upload bootloader).
I used...
Hello, I use nRF51822 based device with s110 softdevice. I noticed that data exchange is different on different connected centrals.
For test I used Windows and Android powered...
Hello,
I have my project up and running using the "nrf51-micro-esb" project. I can successfully set my device to PRX mode and have it receive payloads just fine. Similarly...
Hi,
I have an issue about power consumption with a board nrf52 10040. The consumption should be 100µA but is 500µA. I found an errata about that in ' infocenter.nordicsemi...
We're using nRF52 to read two sensors data: one is an ADC chip using SPI; the other is a PPG sensor using I2C. MCU sampling rate is 250Hz, meaning every 4ms, MCU will poll...
