We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
Im using S130softdevice.i wanna make dimmer by using experimental_ble_app_blinky project on gpioet
But i have a problem with detecting 10 milisecond time (it means...
Hi,
I am new starter in Nordic platform. I am using device nRF51822-CFAC, the SoftDevice is S130_nRF51_2.0.1(Id: 0x0087).
What I am doing is to put NRF51 into system...
Hi,
I'am tring to test the dfu by secure bootloader.I had done all steps like: Test the BLE Secure DFU Bootloader application by performing the following steps .But I found...
I am implementing an SPI master to communicate with an accelerometer using the SPI HAL directly. My chip is marked nrf51822QFACA11609AC. I have implemented blocking functions...
Hi,
When the UART is configured to use FIFO , i use the UNUSED_VARIABLE(app_uart_get(rxdata));
to read a buffer from FIFO.
how can i also receive a number of bytes...
Hi,
I want to do this cycle with GPIO without interrupting it on NRF51 with BLE softdevice:
PIN1 to HIGH level
read value of PIN2
PIN1 to LOW level
Repeat...
Hello, I'd like to do directed avertising to a central which has a random private resolvable address. My idea: both devices share a pre-defined IRK so the peripheral can compute...
I tried, but it does not work.
for(int y=0;y<100000;y++)
{
if(nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_TXDRDY))
{
nrf_uart_event_clear(NRF_UART0, NRF_UART_EVENT_TXDRDY...
Hi,
We have a little issue that we at the moment need to cycle power on v3 nRF51822 after DFU.
We have determined the the reason has something to do with the whole complicated...
I attempted to add spi_master as below, but I am in trouble with link error.
If anyone knows the cause, please tell me.
*** Using Compiler 'V5.06 update 4 (build 422)...
I'm working on a project based on the ble_app_uart_c central example in SDK 12.1. I'm polling the RSSI of a Nordic beacon using sd_ble_gap_rssi_get(), and the fastest update...
I want to handle 3.3v in nrf52832.
NRF_GPIO_PIN_S0S1 -> NRF_GPIO_PIN_H0S1
Can this be this way?
If not, what should I do?
Also, Can the PWM output to 3.3v?
Hi, I use PCA10040 v1.1 and SDK12.1. My desktop environment is Windows 7 64bit.
As far as I know, the J-Link Edu cannot be used for commercial usage.
I so bought...
