Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Inquiry: NTN Support and Application Feasibility on nRF9151
I would like to seek clarification regarding Non-Terrestrial Network (NTN) support on the nRF9151 .
There have...
Hi there,
When flashing my solution to Lesson 6 Exercise 3 using nrf52DK / nrf52832 - I kept getting an access violation when attempting to setup the timer. I compared the...
Is possible to use ble stack for the configuration and disgnostic of a device and that use ieee802154 to make a start network for 1 to 8 devices , where i can find an examples...
I couldn't find anything related to this issue on the devzone, so I hope this can help someone who has the same issue:
We're using the NRF54L15 QFN52 variant with a custom...
Hello,
Setup
MCU : nRF52840
SDK : nRF5 17.1.0
Transport : Secure Bootloader (UART)
No SoftDevice
Custom HW
The Problem: I am experiencing two conflicting...
I have an application running on a custom board using the nRF52840 that uses the SAADC. After migrating my nRF Connect version from 2.6.2 to 3.1.1 the current draw of my battery...
Hello,
I've been having problems in getting the correct battery voltage for a Thingy53 for a number of projects, when using the latest nRF Connect SDK 3.2.1 (Zephyr 4.2...
I am trying to develop a BLE HID peripheral that can be used on Ubuntu 24.04.
When I try to connect the peripheral_hids_mouse example to a Linux machine, it immediately...
I have two problems. This is the first problem.
[Environ]
nRF Connect SDK v3.2.1 nRF9151 (Custom board) VSCode (1.109.4)
The first problem is that debugging doesn't...
Hello,
You've previously provided the sourcecode for nrfutil, before it was rewritten here https://github.com/NordicSemiconductor/pc-nrfutil .
Is it possible you could...
I am developing a FW for the nrf54l15 which should log sensor data into its internal flash (RRAM) and make it read able later from a Smartphone via BLE.
For this scenario...
Hello everyone,
We hope this message finds you well. We'd really appreciate some guidance on an issue we've been encountering in the field.
We have deployed several hundred...
I am dealing with a HardFault occuring in my code, and I am unable to trace the error. The output when the HardFault occurs is <error> hardfault: HARD FAULT at 0xD0D0D02A...
Hello,
I am using the Nordic Thingy:53 and trying to collect sensor data using Edge Impulse.
I was able to successfully connect the Thingy:53 to Edge Impulse and stream...
The device i am currently developing is a battery powered dongle with internal power supply unit for battery charging. I am using nrf5340 USB pins D+ and D- for communication...
