Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hello,
I try to flash my bmd-345-eval board with nrf connect visual in VS code.
But the connected devices don't show mcu but show VCOM0 and RTT on nRF connect in VS code...
Hi
I have a issue, I have 4 samples nrf9160 module, all run in same firmware with FOTA feature
I found that only one module cannot start FOTA, then I try to read message...
I am getting the following build error for a Nordic nRF5340dk
c:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/12.2.0/../../.....
Hello,
We have an issue regarding PSM availability when roaming. Some operators do not grant PSM and once a device connects to such a network, it would drain the battery...
Hi, When performing GATT discovery on the peer device I observe that the procedure takes too long about 5-6 seconds even at the lowest connection interval. The same process...
I was trying to add the nrf91-modem-trace-uart snippet to my build configuration. I've found that it does not take effect when using the "Add Build Configuration" UI in the...
Hi support team
If I want to implement update advertising data dynamically function, which method is recommended?
1. bt_le_adv_stop (); and bt_le_adv_start (adv, ad, ad_len...
Hello,
I am primarily an STM32 user, delving into Nordic. I will be creating a product using the nRF52832. I would like to measure the 32MHz & 32KHz clock inputs to the...
This is a request regarding modules that can be used in Pakistan. We think that nRF9160 is matched for this requirement. Could you please tell us whether nRF9160 is okay or...
Hi, We are using nrf9160 and building the application with CMSE. When my program accesses dynamically requested memory (address 0x200128b0), the program automatically jumps...
We plan to use the Nordic Semi Thingy will be used with Quectel YB0014AA antenna for the demo sites, all located in North America. The Nordic Thingy is fully FCC/ISED compliant...
Hi,
I am evaluating using NRF9161-LACA in a design. Is it possible to activate this chip with esim? Or we have to use a physical sim card for it?
Please let me know, ...
Hello,
We are evaluating a solution for our product where we would like to use
Zephyr RTOS with NCS
nRF52840/nRF5340 + nRF7002 for a combined WiFi/BLE solution. nRF52...
I have been trying the aws_iot sample in nRF Connect SDK v2.7.0 for build target nrf7002dk/nrf5340/cpuapp, in which connect_work is scheduled with a 5 second delay in the...
Hi
I'm looking to understand the IR Susceptibility of the WLCSP. I've seen some post talking about direct IR light causing issues, but not how much of an issue it actually...
