But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
We've been having an issue in the firmware for our project. The firmware will build, program, and run just fine, but if we try to run from the debugger, the debugger will...
Hi, I have two Nordic BLE devices, one nrf52-DK that has peripherial_uart application and nrf52840-DK that has central_uart application. This works well, but the thing I need...
Hello, I am using ble_app_blinky on my BMD-300 evaluation kit (nrf52832) and I want to display a message via bluetooth on my phone with nrf connect. What function should I...
Hi Devzone:
I am not sure if I should ask segger or here, basically I am trying to use Ozone for performance analysis.
I always get this message when starting:
Device...
Hi,
I am a Embedded System Engineer working is a Medical Device Company and presently compiling the code on on a previously licensed IDE and as, the licensing has expired...
Hello,
I'm working on porting a Secure Bootloader application for a project, and trying to understand how the macro is used NRF_BL_WDT_MAX_SCHEDULER_LATENCY_MS.
I don...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/57105/nrf9160-modem-stuck-in-searching/231773
We found sometime the LTE cannot be deactivated during the modem...
I want to try register level programming of Nrf52832 i.e low level programming. I referred your This GitHub repository but there are sill some libraries used . Is there any...
I am running an application with norma NUS Service with bonding.
When I want to make a DFU I start to write a token into the flash with fds and then do a soft reset. After...
Hi, I'm using nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730 to develop a Zigbee Network. I'm using the ble_zigbee_template example as starting point of my works. I seen that...
Hello,
I have an nRF9160 DK and a Thingy:91. Both have been running asset_tracker for more than 3 hours, but none achieved an LTE Connection. I have installed the latest...
Hi, i am working with usb cdc driver (sdk 15.3 and nrf52840) and i have a problem . This is my variables initialization APP_USBD_CDC_ACM_GLOBAL_DEF(m_app_cdc_acm, cdc_acm_user_ev_handler...
Hello,
I send SMS from nRF9160 to my number using following method.
1. Open LTE Socket
2. Send AT Commands:
a. AT+ CFUN?
b. AT + CFUN = 1
c. AT+ CFUN?
d. AT...
Hi all, If using the RC LF instead of a 32.768KHz crystal are there any side effects of the 16ms calibration period which occurs every 4 seconds? I'm mostly concerned how...
