Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT.
Only PB-GATT is turned on, is the device only sending GATT broadcast packets.
However, I now need to...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT. Now,
I need to make a product. Support PB-ADV. And it is an LPN device. What should I do?
I am using...
Hello,
We are currently evaluating the Bluetooth Mesh solution for our product-line that consists of a Bluetooth Gateway that can communicate with battery-powered devices...
Hi All,
I am using light_control example from Mesh SDK and I need to get something that identify my device in mesh e.g id, address. I would like to send some message to the...
Hi,
This is somewhat tricky question.
In my custom board application program using nRF52832 chip,
I used uart initialization function (e.g. uart_init()) and printf...
Is it possible to use a Nordic nRF52840 DK and a personal BLE board to run the throughput example? What types of modifications would have to be made to both boards?
Hi,
after setting up the LPN-example like described here I can establish a frindship relation.
When I measure the current I can not get lower than 40uA.
I use a Multimeter...
Hallo
I am developing on a NRF51822, sdk12, s130,
I have encountered a repeated unexpected reset to my device (the reset reason vector register is all 0)
which seems...
Hi
I have been developing ok with Segger Tools and nRF52DK. My application works as expected. However now I need to send hex files to a customer who also has the nRF52 DK...
I have a bunch of custom characteristics in a custom service. I have two different modes of operation that I need to handle and the data associated with these custom characteristics...
Combinig a simplified version of the bsp example and the pin_change_int example I noticed that I'm running into an "[NRF_ERROR_INVALID_STATE]" error caused by nrf_drv_gpiote_init...
I'm trying to send a DFU file but i get en error:
2019-08-16T16:11:40.300Z DEBUG Destroying DFU transport. 2019-08-16T16:11:40.300Z ERROR DFU failed with error: When writing...
DIODE_FWD_VOLT_DROP_MILLIVOLTS is normally depending on how the reverse current protection is implemented in hardware. the current value of 270mV is adapted to the used diode...
The coap_client sample is not building for the nrf9160_pca10090 board. I'm using v1.0.0 of the nRF Connect SDK. The commands used from the coap_client directory are:
mkdir...
Dear Nordic experts,
I am trying to profile embedded S/W on a custom board (call it board #1) with a nRF52840 on it. On this board the trace pins TRACECLK and TRACEDATA...
