Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
I am implementing a background DFU bootloader and uses the example from Vidar Berg ( https://devzone.nordicsemi.com/f/nordic-q-a/46994/background-dfu-application-source...
Hi,
I have just updated my app from SDK 15.2 to 15.3 (and the softdevice from 6.1.0 to 6.1.1).
Now nothing is working... I initializes a button with NRFX_GPIOTE and now...
Trying to set up attribute reporting I thought I had found a solution but was apparently wrong. My coordinator is sending an attribute reporting request with a minumum reporting...
Hello,
I'm using nRF52832 in a sensor PCB card, and I want it to have an antenna. Now I'm drawing the schematics of the PCB using KiCad, but there is one problem I can't...
Hello Nordic team,
Sorry for the ambiguous question. Let me know if you need further clarification about the question.
Currently we have a nRF52 based HID device....
Now that nrfutil has been ported to Python 3, I've been trying to get a DFU controller set up on a Raspberry Pi 3A running Raspbian Lite. I've built and installed the pc-ble...
Hello,
I have a query regarding the exponential waiting period behaviour when pairing fails under repeated attempts. In the Bluetooth Core Spec v5.1 Vol 3, Part H, Section...
Hi, Nordic!
We have connected gpio pins to usb data line pins for using usb or i2c in different times.
But even if USB core disconnected, usb lines hinder for i2c lines...
Hi;
I am trying to send a Telegram message using Telegram Bot API . As the documentation shows: "All queries to the Telegram Bot API must be served over HTTPS". I have...
Hello,
We are using NRF52840 and for a specific use case we will install our module on an M.2 (A/E) breakout. In this configuration USB will be the main communication interface...
Hello,
We made a small replacement on the event handler of the ble_central/ble_app_uart_c application, just to do a loopback to test the UART module.
Here is how the...
The Boron module from Particle is a nRF52840 with a uBlox LTE CAT-M module, available for $50. It's small and seems like a fun module to prototype with. I'd like to use SES...
Hello,
nRF52840-DK
SDK: 15.3.0
SoftDevice: s140
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52832.ps.v1.1%2Fclock.html
Do any drivers...
Hi Everyone,
We are using NRF52810 with latest nRF5_SDK_16.0.0 and s112_nrf52_7.0.1_softdevice. We are able to program with ble_app_UART example on our prototype,
but...
I would like to set or clear a digital pin when the button is pressed.
I seen to have achieved this with the on-board button but it doesn't work with a mesh switch.
...
