Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi
I have a nRF52832-DK based central node and multiple nrf52832 based peripheral nodes implemented using a combination of ble app uart c + multilink central at the central...
Hi Guys,
I am trying to access the serial number written on MCU through software.
White strip on MCU has details such as PCA10056, 1.0.0, 2018.04, 683xxxxxx. I am trying...
The Qorvo QM14501 LNA in nRF9160 reference schematic seems to be consuming several mA of current, which is quite a lot for a GPS LNA. There are other LNA chips in the market...
Hi
When I use the nRF5_SDK_14.2.0 of nRF52832, the example is selected ble_app_uart. And the Android example is the Android_UART_Client_Bluethoot_Sensor_Nordic_CortexM4_NRF52832...
Dear team, Device - nRF52832 SDK - SDK_15.0.0 IDE - Segger Embedded studio Softdevice - s132_nrf52_6.0.0 I am doing buttonless DFU in my application. I have successfully build...
Hi,
I want to use uart. I configured two uart, uart0 and uart1. I want to read and write to one uart using APP_UART_PUT and APP_UART_GET. how it possible without uart event...
I am trying to modify tx settings in open thread but when I try to execute otLinkSetMaxTransmitPower it cannot find this function. It seems to find all others. Is this not...
Hello,
I'm using a nrf51422_xxac_s110 chip, with the 12.3 SDK. My code is based on the ble_peripheral\ble_app_uart example in the 12.3 SDK. I'm hoping you can provide some...
Hi,
We believe we have either a BT communication issue for Nordic Semiconductor ASA NRF52832-QFAB-R
https://www.digikey.com/products/en?keywords=1490-1055-1-ND
...
The comport generated by the USB CDC UART example is showing up as a comport; However when I start sending something my terminal program is crashing.
When I look in the...
I've been trying to run the LWM2M sample from here but I've been running into some issues. Leshan provides two URLs for publicly accessible test LWM2M servers, coap://leshan...
I am using RIGADO Evaluation Board 320-00050
I am using nrfutil v5.2.0 to perform DFU i am able to create DFU package and when sending the package i am facing problems ...
Hi
I combined ble_app_uart with relay example .I am getting a multiple definition error in app_uart_fifo while building.I have added required .c files and their header paths...
