After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I inherited a Nordic Semi firmware project. It was developed using s132_nrf52_4.0.2softdevice.hex and SDK 13.1.0.
How can I download these versions? I would like to start...
I installed the nRF5_SDK_15.1.0 compiled and ran the ble_app_att_mtu-throughput example.
The first run was using the default settings all went as expected. For the second...
Hello Nordic team,
I am working on ble_peripheral example. Initially application binary file size is 100 KB but after adding support of FDS application size increased to...
Hello,
I have read through all the posts I can find on this subject, but none has solved my problem.
- nRF5_SDK_15.1.0
- Example: Segger Embedded Studio Project: twi_master_with_twis_slave_pca10040...
I want to fully understand the use of RTOS in conjunction with the stack. As an example, I took an example ble_app_hrs_freertos (SDK v15.0).
Add a service, for example...
I need to count the pluse number use 51822, the frequency about this pluse is about 0.01Hz to 1Hz and is not fixed, I know use Time1 can achieve this funtion, but the problem...
I wriing softdevice ,aplication and bootloader by nrfprog tool.
But,the device works with the bootloader, not the application.
After writing, it is reset and flag is set...
Hi
I am using fatfs of nRF5_SDK_15.0.0_a53641a. Iam writing a program with keil.
I am trying to save data using SD card now.
By using fatfs example it was possible...
Hello all,
I wanna ask smth related to the use of the nRF52 as a HID keyboard (USB host).
I have already played around with the SDK example ble_app_hids_keyboard and tried...
Hi,
I'm developing a product with the NRF52832.
I have one Blue LED (APA2107LVBC) which is driven directly by a GPIO as shown below :
With a typical Vf of 2.65V, the...
Hi,
I'm trying to implement the following use case:
On the first button push a sensor advertise and bonds with a smartphone. I do it the following way and it works fine...
I tried to configure OTA in my application, but nrf toolbox stucks in "enabling dfu bootloader" and I can see "Starting DFU" showing up really fast, can it be a problem with...
Edit : I solved the problem. The problem was related to variable declaritions and pointer. None of the commands was not working except Write Register and Read Register. I...
Hello. For my application, I have written several functions related to sensor interrogation and work with some periphires of the controller nRF. I split these functions into...
Hi, I started development using a custom board with nRF52840 QIAACO. 1. The prototype uses Holyiot-18010 module ( listed on Nordic 3rd party modules). 2. I am using supply...
