Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi all!
I use the ACM_CDC USB class to transfer a batch of data (150MB) from the MCU (nrf52840) to the host. Currently, the system reaches up to 100KB/s upload speed, although...
Hi @ll, I have the following problem: There are three unprovisioned devices with UUIDs containing a 0x0A byte but the scanner within the pyaci script shows 0x00 instead. Device...
Hi.
To avoid via in PAD I like to route a signal/pin from the inner row (closest to center) through a pin in the outer row.
However, to be able to do that I must be sure...
We are using SDK_13.0.0_04a0bfd and want to change the location and size of the bootloader in flash. But when we do this, the bonding process in the main application doesn...
I'm a newbie to nRF5... I just installed latest IAR, nRFgo, Segger J-link & nRF Connect on Windows-10. Segger J-link appears to have updated nRF51 Dongle to 6.3. I get the...
I'm developing firmware for a client that includes a connectable beacon. I'm using code based on a Nordic example, though I can no longer find the original. I'm trying to...
In our project nrf52 device scans for nrf52 beacon device throughout the day. It scans number of beacons available and send it to esp32 device on serial. that is how its working...
Hi, Everyone
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
The size of the file has increased dramatically when I run mergehex.
1. nrfutil settings...
Hello i'm currently working on the central part of the DFU i succeded to make it work and now i'm working on the link loss part.
I used This to make the DFU work but it...
Hi,
I am facing the same problem as in question ' USBD don't work with debugger ' from @ Dusautois Jérôme
I am trying the same code both on PCA10056 and my board. In PCA10056...
Hello! I am useing nRF52832 with custom-made board.
SD 5.0.0 and 14.0 SDK
I am using modificated example of "ble_app_template", i added simple custom service from example...
I'm using USB based DFU on Windows and on Linux 18.04 LTS VM on Windows.
Platform: nRF52840-Preview-DK
SDK version: 15.0.0 (nRF5_SDK_15.0.0_a53641a)
example USB Secure...
Hi everyone,
I was just going through the library functions provided here in this link : nordic functions twi
But inside all these functions ,there is this parameter...
platform : nrf 52832 SDK : 14.0.0
I used gpiote to detect sensor's interruption . there are two sensors ,so I configure the gpiote like this :
neither of the two sensors...
Hello, I want to ask if is possible connect nRF51 Dongle in Shield Host USB ( https://www.electrofun.pt/usb-host-shield-android-arduino ) with arduino .
Thanks very much...
