Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi. I am using nrf52832 SoC with s132 device (4.0.2). Device is acting as peripheral, I have set max BLE connection limit to 1. ble_cfg.gap_cfg.role_count_cfg.periph_role_count...
I'm following the migration guide from SDK 14.2 to SDK 15 , and am a little hung up on the new nRFx module.
All the examples in the new SDK use the legacy drivers but the...
I'm using the CR2032 to power up my nrf51822 with LDO setup, it works well in the begining. But when the voltage drops below 2.6V, my phone cannot scan the BLE. Is it little...
What is expected behaviour of s132 device (4.0.2) if peripheral is initialized with periph_role_count=1 and somebody tries to connect when BLE connection is already establsihed...
Hey Guys,
I'm a newbie on BLE development , I'm trying to run the example "examples\ble_peripheral\ble_app_ancs_c" , It works well first time, but it cannot receive the...
I'm using nrf52832 powerd by a 3.6V regulator in a li-ion powered application. And using one of the IOs (P0.05) as the power supply of other circuits.At the same time, using...
Hi
I am having trouble getting the basic BLE_APP_UART up and running. The UART printf() works, but the BLE module (NORDIC_UART) is not visible in all the devices android...
hi,
i am doing a project where i am using central and client model.
i am using nrf52840 as central device and thingy 52 as peripheral device and i am using sdk 14.2.0...
When using make flash on an SDK11 sketch, s132, pca10040, on Ubuntu 18.04, it successfully builds everything until app_uart.c; when it gets to that point, it outputs the following...
Hello,
I would like to test my code on a NRF52832-QFAB chip with 256kB chip to see whether my code fits into the 256kB flash variant.
According to nRF52832 Rev 1 Errata...
hello
i am using segger embedded studio. with nrf52840 and sdk15.
i was working to set the clock using nrf_clock_lf_cfg_t which is defined in nrf_sdm.h .
nrf_sdm.h is...
Dear Sir/Madam,
I am working on a 51822 project which send data to Android App. This project is actually an replacement to an old BLE sensor which is obsolete now. I have...
HI.
I use the peripheral example of SDK15 to implement functions such as uart, spi, and interrupt.
However, if soft device S140 is programmed, then my code is not programmed...
Hello, I am currently writing firmware using NRF52 SDK 11.0 (there are plans to port to SDK 15 eventually, but for now I need to get it running with 11) on Ubuntu 18.04. After...
