Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I want to start developing for Ble Mesh
I own:
PCA10056 x2 nrf528240 Preview DK
PCA10040 x1 nrf528232 DK
PCA10028 nrf51822 DK
I want to buy more to develop...
Hello, you great people!
I'm working on a simple project where a transmitter wakes up a receiver and it's working just fine. Currently working with NRF24LE1 modules. The...
Hi All,
I want to send data, like some number, via BLE from smartphone to nRF52. I have to use an external module for this project, because my application uses also bluetooth...
Hello,
I'm using nrf52 with SDK 11 and softdevice s132 v2.0.0. We are close to release our product for testing and I need to add DFU on it. The non secure bootloader is...
I am trying to upload a bootloader to an nRF52832 chip. (This chip is on the ruuvitag and is programmed through their developer board).
I got the bootloader working on...
Hi all,
I'm attempting to develop a feature that will allow our users to personalize their device name. The user will have the ability to change the device name while connected...
Hi
I add the fstorage to ble_app_uart on the SDK v14.1 to work on nRF52810. After fstorage initialization, I could write data to flash.
However, if I write the data...
Hi, I'm testing the light control example from Mesh SDK 0.10.1.
Although I have received an answer about the future plans of mobile Mesh SDK from developer Hung Bui that...
Hi,
I have some data which i want to send from nrf51-dk to ESP8266 . i have tried Ble UART central example to write data serially but doesn't achieve any result. I have also...
I have 2 Channels with SAADC taking samples. They are configured to respond to BLE characteristics that have read and notify properties, each channel has its own characteristic...
Hi,
As in the Product Specification of nRF52, pin number 9 and 10 are configured as NFC pins. However, this setup is conflicted with our pin mapping for other sensors in...
I am trying to store a small amount of data on the nRF52832 with the FDS module.
I followed the following code found in another question:
devzone.nordicsemi.com/.../...
Hi,
We are currently migrating our codebase from SDK 13 to SDK 14 for NRF52832 based board. One major difference we see is that SPI transfer completion callbacks are not...
Hi Dear Nordic!
We have prepared 200 pieces of PCB (used nRF52840) to pre-test our Product.
Now we are waiting for nRF52840 IC to solder.
Is it possible to buy ~...
