Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I have a problem with advertising, application starts advertising and makes connection normally, but after disconnection advertising is not starting. sd_ble_gap_adv_start...
Hi,
i am using SDK v8.0
and in main function, initialization like this err_code = bsp_init(BSP_INIT_LED | BSP_INIT_BUTTONS, APP_TIMER_TICKS(100, APP_TIMER_PRESCALER), button_event_handler...
Test code：SDK14 ble_app_ancs_c
Hey guys,
When I used ble_app_ancs_c demo to do FDS, there was a problem！
I initialize FDS and register the drop back function。
When...
I am migrating a project from SDK 12 and SoftDevice S132 V3.0.0 to SDK 14 and SoftDevice S132 V5.0.0. Is the follow case still required in the ble_evt_handler ?
#if (NRF_SD_BLE_API_VERSION...
Now want to use two way PWM, how to set the PWM cycle, frequency, duty cycle, there are two road PWM phase, which is the starting point is not the same as shown in figure...
I am having errors building the examples in the latest SDK for Mesh (nrf5_SDK_for_Mesh_v0.10.0-Alpha_src). I ran cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf52840_xxAA .. in...
Hello,
I'm using NRF52832 with SoftDevice S132, and SDK 14.0.0 to make NUS peripheral and central. To test it I have one NUS peripheral device, that echoes incoming data...
Using SDK 13 FDS, I store 6468 byte, that is 1617 words, including FDS header. Of course this size is total.
In detail in byte size, this size consists of
(12(header)...
Hi,
I'm wondering if the slave connection interval range is the same as the GAP peripheral preferred connection parameters i.e. does it make sense to do the following ...
Hello!
I'm developing thread application with COAP communication. I've got problem with message queue on router. Everything works fine when operating as a child. I have cyclic...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I'm trying to get started with the nRF51-DK with the ble_app_template. I want to get it working in the Rowley CrossWorks IDE. (From what I understand this is the same...
I am having trouble running softdevice_enable. Here is what happens:
After main(void) starts the code is:
log_init(); // WORKS
clock_init(); // WORKS
buttons_leds_init...
Hello,
I'm using a nRF51822 to send data to the iPhone using the NUS service. I'm using the oldest SDK4.x and v5.x S110 soft device. I know that the least connection interval...
