This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I am currently trying to power profile all aspects of the nRF52840, which includes the CryptoCell 310. The instructions say "
Testing
Test the CryptoCell Example...
I tried to use Timer2 as counter with event and interrupt. event is working. interrupt not.
<pre><code>
timer_count_cfg.mode = NRF_TIMER_MODE_COUNTER;
err_code = nrf_drv_timer_init...
s132_nrf52_5.0.0-3.alpha_softdevice.hex (/attachment/26a9916e1af8c97bcba7185035bd7b31)Hi, I am starting to work on NFC and Bluetooth pairing for the nrf52 and i tried to compile...
hello everyone：
do you have try to add wdt into bootloader project?
i add it as follow：
in the static void wait_for_events(void) function, i add two
if(NRF_WDT-...
Dear all,
I want to develop applicattions for the board nRF52840 Preview DK. I went to the download section of this board , and i saw the following software nRF5x-MDK-Keil4...
Hello,
I want to use NORDIC nrf52 to perform some power consumption Analysis. Is there any eveloution board from NORDIC that don,t have debugger connected to it? I want...
Hi all,
Is there a tutorial that explain better the bonding information and whitelist? I have more doubt about that.
My first code i have pairing and bonding:
...
hello..
I'm actually working on nrf51822,i could complete the advertising part successfully("hello world")..NOW i want to add privacy feature which allows an advertiser to...
Hi there,
I am working on the SDK13 project template that I am modifying in order to install a vendor type uuid.
But my code crash on "advertising_init" and ble_advertising_init...
While using the secure bootloader image and test application works consistently using the development kit I have not been able to port the solution reliably for our custom...
hai
i am using mbed to program my nrf51822.i want to set the analog pin p6 as analog in in one situation and as a digital out in another situation. but i am unable to do...
Hello.
After executing the code below, the RAM was dropped and the program could not be written.
for(idx = 0; idx < 7; idx++)
{
NRF_POWER->RAM[idx].POWER = (POWER_RAM_POWER_S0POWER_Off...
I'm studing the project of ble_app_gls/PCA10040/SDK11.0/ ,I have got some questions about the RACP indication pending and retransmittion mechnism. In this project(File ble_gls...
