Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
Does the .hex file for V7.1.0 include the master boot record? I'm writing a JLink script to flash it and I'm trying to figure out, once converted to a binary file,...
I have the PCA 10028 Board. I would like to add a characteristic on an already existing service.
In the nAN-36 I see, what is necessary to set up service and characteristic...
Dear Forum,
I just unwrapped my new nRF51 DK board and already played with some mbed example programs which worked beautifully! So first of all - thank you Nordic & mbed...
What capacitors would you recomend for this 16MHz Quartz http://www.jauch.de/ablage/med_00000848_1411137106_JXS32-180914.pdf to ensure 40ppm frequency tolerance for nrf51822...
I read the following but was not able to use it to resolve my problem.
devzone.nordicsemi.com/.../
bootloader.hex
bootloader_settings.hex
The bootloader address...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello,
I would like to use the PCA10031 Dongle as the peripheral with the multilink examples. I will be wiring up a button to the available GPIO and using this for a space...
I want to use to set the UUID in my Nordic device as following:
Base UUID:
{0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,...
hi.
I refer at the example find here link text .
i want to transmit with Advertising, as the temperature is transmitted in the example, data from some sensors .
But in...
I'm trying to port the HRS example using S110 Softdevice and SDK 7.1.0 to IAR 7.10 on the pca10028 board.
I've created an IAR project which uses the same files as the Keil...
Hi everyone,
I am trying to create a file in sd card but it is not creating.But i can read a file from sdhc card of type .txt,.c,etc with nordic evolution board nrf51822...
Hi all -
I want to use the device manager (SDK 7.1.0, SD110) to do a simple nRF51822 implementation where after the first bonding happens, and is stored in flash, the nRF51822...
Hi
I have a board with some extra bits and pieces hanging off the SWD lines.
This means the SWD needs to run at a lower speed (500kHz or less). At the lower speed, Kiel...
Hi,
I'm trying to build my IAR project but it's not clear to me what I should link against to resolve symbols referenced by the soft device headers.
Thanks,
Kenn...
Hello,
Is there any reference designs / documentation or ideas on how we can wake up NRF51 when there is radio activity on a specific frequency ?
In our design, we need...
