Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I have a PCA10056 (nRF52840 DK) and while programming it with a UART example from the nRF5_SDK_17.1.0_ddde560 using Segger Embedded Studio for Arm 5.42a, it will not show...
Hello, I have one smartphone with Android and one ith iOS with NRF connect application and I can't see, only on iOS, the Primary and secondary PHY used by my advertiser device...
Hi everyone,
We have devices using the BLE module (nRF52) deployed in clinics for testing. They have been functioning without issues until recently when we noticed occasional...
I'm using the nRF54L15-DK to run a Bluetooth peripheral_hr project in DCDC mode, but if I write
nrf_regulators_vreg_enable_set(NRF_REGULATORS, NRF_REGULATORS_VREG_MAIN,...
Context: I am working on a project to monitor up to 880 devices in an Industry 4.0 warehouse. The warehouse is divided into 16 areas, with each area housing 30–55 devices...
Hi everyone,
I’m a complete beginner and need some help. I’m working with two XIAO nRF52840 Sense boards: one as a central and the other as a peripheral. My goal is to send...
Hi,
I am trying to use a digital channel to sync with a current measurement. I have connected VCC, GND and a digital output of my DUT to the PPK2. I can see from the scope...
I am evaluating a Fanstel BC805M device, which uses the nRF52805 chipset. I am using VSCode and have installed the nRF Connect Extension Pack, toolchain v2.8.0, and SDK v2...
I programmed a nrf52840dk board (PCA10056 3.0.0 2022.7 1050288497) as a sniffer. It works well.
Now I want to flash it to zephyr samples/basic/blinky by "west flash". west...
Hi,
(nrf52840, custom device, nRF5_SDK_15.3.0_59ac345)
I am working on a BLE project involving one central device and two peripheral devices using BLE NUS. The peripheral...
Issue with debug on the PDK eng_rev_B PCA10156
Segger does not recognize the chip and debug fails across multiple sample applications
debug message results:
JLinkGDBServerCL...
Hello,
We are investigating a compatibility issue between our devices running nRF5 SDK 12.3.0 with softdevice s332 v2.0.0 and a Motorola Edge 50 smartphone. From BLE sniffer...
Hello,
Does the nRF54L15 have multipoint?
In my application, I would like to have different devices connected simultaneously, so I was looking for something like multipoint...
Hello,
We have a Nor flash connected to the QSPI and another peripheral connected to the classic SPI.
Due to the errata [159] , the HFCLK128M is running at 64MHz and...
