Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hello,
I am currently working on a BLE Mesh–based control system and would appreciate guidance on a few architectural and scalability concerns.
System Overview The network...
According to the working principle of a crystal oscillator, the load capacitance is inversely proportional to the resonant frequency of the crystal, that is, the larger the...
Hi,
We are using the NORA-B126-00B module on our custom board, and the first time we flashed it with a simple LED blink example, it worked fine. However, after erasing the...
Hi,
I'm looking at the watchdog behavior in mcuboot during DFU. Here are the watchdog-related configs I've set:
and here are a few things I've noticed:
- Even though...
hello, When I switched from the NCSv3.0.0 version to the NCSv3.2.1 version, I encountered the following compilation issue. How should I eliminate this "Error 1 (Ignored)"...
Background: Our tests on SDK 2.5.0 showed that it was possible to maintain a Bluetooth connection at a distance of approximately 180 meters with the following initial advertising...
i am performing DFU process b/w nrf54l15 and nrf connect mobile_app ( Android ) and i am sniffing the it using nrf54840 soc and the bord is nrf21540dk in Wireshark i know...
Hi,
I am currently working with 2 nrf54L15-DK and a seperate 4 antenna array.
For my tests i run a 2x2 antenna config with preferred peer set to 1 and 4.
I was now...
I just got the board, installed the nRF connect sw. Then installed the J-link, connected the board, power it on and run the quick guide, but it searches and doesn't find anything...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
I'm running the nrf5340_audio_dk and using version 2.6.0-rc1. When connecting one NRF5430 as headset to another NRF5340 gateway, running BIS mode everything works fine. But...
Hi,
We've been working on an IoT device that uses an nRF52840 in a pre-approved module from Moko. We are getting ready for a commercial launch in 2026, but I am very confused...
I have noticed that the dts file includes the configuration for arduinio_spi, along with the corresponding pins associated with spi4. However, I am unsure about how to utilize...
The Bluetooth 6.0 Channel Sounding feature supports multi-antenna functionality. The nRF54L15-DK development board is currently single-antenna. Is there any official documentation...
