I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi,
Need help to interface nrf9160 with MSP430.
Making Project where MSP430 will collect the data from ECG sensor and sending to nrf9160 in packet form. nrf9160 will going...
Hi,
Time to time, Our board stuck in QDEC_IRQHandler.
1) In which case QDEC_IRQHandler could occurs?
2) I want system reset from QDEC_IRQHandler automatically.
But...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
During development, I was wondering about advertised packets.
I thought that the advertisement packet...
Hello ,
I have configured one nrf52832 where it sends temperature data over one service's characteristics ( updating the value after every 1 min ) and I am able to see this...
Hello. I am trying to scan for BLE packets and write them out through USBD using nRF5 SDK v15.3.0. I am calling app_usbd_cdc_acm_write() in scan_evt_handler when an event...
If I update prj.conf in a zephyr project, but I'm building with segger and the connect sdk (1.5.1) do I have to do something besides "Build / Rebuild" to get segger to recognize...
Hello Nordic Experts,
I almost finished the development for my mesh project with nRF52840. But I faced some t ricky issues when in mass production. that is the time for...
Hi,
I am using SDK15.3.0 and s132_nrf52_6.1.1_softdevice. (nRF52832)
Getting higher current consumption ( 300uA ) while using the PWM library. ( https://infocenter.nordicsemi...
Hello, everybody.
I bought the nrf5340-dk board and tested the zephyr sample code. The Blinky code is worked. I tried the beacon sample code. But it is not worked. I think...
Hello ,
I have interfaced one NTC sensor with above attached image and below information :
SAADC pin : AIN2 ( NTC - pin )
VCC_nRF voltage = 3.3V
R14 = 51KOhm , 0.5...
Hi Team,
We have some application for using the oversampling code but we are facing some issue in that, we try to use the oversampling example to ours code but its calling...
Dear sir,
When use the template project(Which is in peripheral) for UART tx & rx is not working in without debug, but if i use base project(Like uart) file it is working...
Hello, I've seen some similar questions about resets after downloading firmware, but haven't been able to find the solution to my problem.
I'm using a Minew MS88SF3 NRF52840...
Hi,
We have a working application that allows FOTA when using the SDK 15.2 bootloader. We have recently tried to migrate this to SDK 17.0, and everything works except for...
