i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi all,
I am currently working with nRF52832 boards, and I am trying to save some values in my flash memory. I have already created a code for this purpose and I am able...
Hi, I'm currently trying to understand multi-Link and Immediate Alert Server Application (ias) examples in SDK 17.
While I'm analyzing them, I got some questions:
Q1)...
Hi,
I am working on the nRF52832 ,why i can't able to set the low 7.5 ms interval . I am getting the error at ble_advertising_start . Do I want to change anything else?...
We are preparing our nRF52 product for the unintentional radiator test. Currently, the SoftDevice is enabled and we have the low power mode disabled with the following changes...
Hi,
Looking for some guidance on how to use the 'cryptographically secure random number generator' in a Zephyr/nRF Connect SDK application on an 52840
Is this a supported...
Hi sometimes it happen with my nrf52832 based device. The common way I am programming firmware during development is next:
nrfjprog --program fw.hex --sectorerase --verify...
Hi,
I am working on the nRF52832 ,If i want my data to be transmit every 7.5ms then what should I set the minimum connection interval and maximum connection interval ? please...
Regarding that the nrf52811 is able to use direction finding, there is any example for configure a tag with the nrf52811 to be located? Did nordic finally release any AoA...
Hello,
Sorry if it will be long. thanks for the help.
Using nrf9160 dk. The first thing I want to ask is about is the pins. I want to make sure I am using the correct...
Hi
I am currently using nrf52840dk with zephyr, and SPI used to work fine.
Now, as a slave, the kit only reads the data read while MISO is high (this might be what's supposed...
Hi, I am trying to create and FOTA upgradable application on the nrf52811 SoC. I have managed to do the same for nrf52832, but when I repeated the process for nrf52811 it...
Is it possible to use multiple NUS client with NCS ?
One of the problem i see is that nus client callback (bt_nus_client_cb) don't have information about the connection...
Hi,
My application needs to enter DFU mode based on a command from another device connected via SPI.
I see that I could use the following two statements once the application...
In the nRF5340, is the application processor able to run concurrently when BLE transactions are happening?
In previous generations of the nRF family, the application stalled...
Hi everyone,
I am trying to understand the GATTS Handle Value Notification diagram.
From what I have understand so far is tha the soft device keeps a buffer (ATT table...
