Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
SDK16
S132
nrf52832
SES / Windows 10
After much searching this site and the web in general I'm reaching out for support.
While in low-power mode I'm seeing a pulse...
Hello im an Android developer and we have an app that uses an older library but still works with are older products.
we currently use
implementation 'no.nordicsemi.android...
From what I read on DevZone it seems that there is a limitation in nrfutil when needed to update BL+SD+APP. NRFConnect over BLE manages the 2 separate downloads (BL+SD and...
Hello there The problem I encountered was that when getting the slave service, returning to get the service failed. I used DEBUG to check the p_ble_gattc_evt->gatt_status...
Hi,
I am using nrf Connect SDK v1.2.0 in Segger Embedded Studio 4.52 and developing on a nrf52840 development kit (pca_10056). I use the "configure nrf connect sdk project...
My goal is to establish a BLE connection between the DK and the smartphone, using NFC for the OOB pairing . I am using the nRF52 DK and the nRF5 SDK , v.16.0.0.
The intended...
Hi,
I am having issues with getting SPI up and running on my nrf52840-DK using NCS. I've tried getting support about this in another ticket but it seems like it lead to...
Hi,
We are using the nRF52840 SoC.
The following image is taken from the datasheet:
It shows a Gain block before the SAR core
a. Does the Gain block serve also...
Hi ,
I want to know if it is possible to close/open the uart connection with RTS and CTS pin in order to have a low power UART?
When RTS and CTS are high, uart is closed...
Hi,
Can any Zigbee application receive ieee radio interrupts in both TX and RX path?
What I need is:
In the case of Zigbee Tx, an advance notification of 200 μs would...
Hello, I am using nRF52 DK and softdevice s112, developing with SDK V15.2. I am exploring the fds library and have encountered some strange behavior. When I connect the nRF52...
Hello,
I am using nRF52840, S140 v7.0.1. We want to measure distance between two nRF52840 with BLE 1 Mbps and 0 dBm.
I am referring below two links.
In this its...
Hi,
We have 2 microcontroller on board. One of our micro controller will update nordic chip using serial DFU without any signed keys.
For testing purpose i am implementing...
Hello,
I'm new to Nordic products.
I have BL651 module and I want to connect it to another CPU over UART. So my question is how can i do it?
I've found in some other...
