Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I've tried for two days to log back into the cloud service and just get the spinning angles. I tried to create a new account and the same. I was able to change the password...
Hi all, I would like to implement a fault handler in our nRF9160 based system to handle hard faults/unhandled exceptions by resetting the system, but am having a hard time...
Dear Nordic team,
I have a running NRF52 with a firmware based on the freeRTOS demo. To this demo I added the PDM Support Module and the TWI Module.
As soon as both sensors...
We are trying to implement models inside the mesh. So we've started with a functional example of the generic on off and tried to update it according to our needs.
The custom...
Hi,
I have 3 devices that all act as broadcaster and observer they continuesly sending data to each other, now i want to establish a connection between one of those 3...
Hello,
I have 2 pieces of nRF52840 and I managed to connect each other. One is central, uploaded the code: 'nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_multilink_central...
NRF52832 DUF success but when download from segger studio, Jlink RTT viwer print NO DFU found, but when download bootloader from segger stuio, can not entry app
Dear Nordic...
Hello all.
I need to work with the RTC especially its events and interrupts, and I have some misunderstanding after read its manual.
I need to use it for low power systick...
Hello,
nRF52840-DK
SDK: 15.3.0
s140
IDE: SES
How do I maintain the persistent flash data I have using the FDS while also using DFU. I have seen several older posts...
Same as Case ID: 234629 .
Calling modem_info_short_get for the parameters MODEM_INFO_MCC and MODEM_INFO_MNC fail.
I suspect the problem is in code. Tracing the MCC call...
I've made a project that scans and advertises.
The first problem: When i have one central link, I get the problem that the client service gets events twice.
<debug> ble_db_disc...
I'm using nrf52840 SDK V15.3.0 SoftDevice S140. I want to test long range feature and 2mbps mode also . How to add these features in SDK example code like ble_app_uart or...
Hi guys, i'm playing a bit with the ble blinky peripheral example, as a precursor to a bigger project.
What im trying to do is disable the services completely, meaning that...
Hi all,
I am trying to emulate a device with ble-driver-py. What I am looking is to have a device advertise, provide few services with respective characteristics (read,...
