I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello,
I am working on a project which requires radio transmitter and receiver to work in sync with the SPI. So the setup is as follows the Transmitter transmits a signal...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
Hi,
I am running IoT LWM2m example. Everything were going fine since yesterday. when I do hcitool lescan, i see following output:
hcitool lescan LE Scan ... 28:45:8B...
I am using the ble_blinky example (s132) and want to increase the number of characteristics. I get the error code 4. I think the storage capacity is not the reason why I can...
Hi Team Nordic,
I started developing a project using SDK 15 using DK nrf52840 .
I went through several threads and started by creating a test folder inside example directory...
Hello,
I have the proximity example updating the battery service value fine using the provided nrf_drv_saadc.h driver. When converting the saadc driver to NRFX (nrfx_saadc...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
It seems to me that unused GPIO pins can stay float. However, earlier questions made me less confident.
Is firmware setting is enough?
Thanks,
Daniel
1. Is it reasonable easy to get a stable throughput over 1Mbps at a 3 meters range? 2. How much CPU resource is available at above situation? Or how many DMIPS is left at...
Hi
I am working with S130, sdk12.3 NRF51422_xxac
I have been successfully testing bootloader DFU example (secure_dfu_secure_dfu_ble_s130_pca10028) on the NRF51 dongle...
