Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I'm trying to implement the buttonless DFU service example for SDK 12.3.0 into my own project, but when I call ble_dfu_init my compiled .hex file becomes 10 kb larger...
Hi,
I am working on SDK-14.2 and after execution of code i get this two error mention below.
sd_ble_cfg_set() returned : Unknown issue when attempting to set BLE_CONN_CFG_GAP...
Hi I have implemented a controller device using nRF52832. The controller device is installed in an industrial control box where it is used to control relays that subsequently...
Hi,
This question might be a little bit off, but not to far off for this forum I hope.
I am considering the nRF52840 Dongle to gain a better understanding of a issue...
Hi guys,
I need to get MAC address of my device and put it into characteristic? Is it possible? And maybe someone can tell how to implement this?
Regards,
Konstant...
Hi:
I use heart_rate_collector project in pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver/blob/master/examples/heart_rate_collector/main.c )to connect...
Hello,
we are studying component base for development Wireless Hearing Aid device.
trying to understand limitations and capabilities of your nRF51822 SoC.
1. Can...
When test the current in the WFE state.
If not use the DMA, the current is not exceed 0.1mA. And when have used the DMA, the comsumption is very high , the current is about...
Hi,
We have a custom board with nRF52832 QFABB0 chip. High frequency crystal used is 32MHz (Part No: ECS-320-8-37CKM ) with two 12pF load capacitors (Part No: 80-CBR04C120F5G...
Hi All,
As "Mesh beaconing example" work as a advertiser and at a same time it scan beacon also.
I just want to use only beacon scanning functionality in this application...
Hi
I have moved an application from Softdevice 130 V5.1 (with SDK 14.2) to Softdevice 130 V6.0 (with SDK 15) both using keil.
My BLE peripheral device name is Nordic1234...
we are using NRF52832 for a project design, I am a bit of afraid of BQB certification, I think add a such like Johanson 2450FM070029 ceramic filter in front of antenna, (...
Hi guys,
I will begin the bluetooth mesh structure part of my project. I looked at this topic to learn what I have to do for creating a mesh project at KEIL. That guide...
So I have a NRF52 DK PCA10040 V1.1.0 2016.15 and a NRF52 DK PCA10040 1.2.4 2018.23....
the 2016, when connected to my laptop by usb, produces 3.3 volts on vdd....( sb10...
