Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have a smartwatch, smartphone, and tablet.
I went to some place without any other bluetooth devices, my devices are able to scan and pair with each other. But nRF-51 not...
Hi,
I have followed sequence in http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fsdk_app_serial_dfu_bootloader.html&cp=4_0_0_4_3_4...
Hi,
I have a beacon code for nrf51 that I wanted to port to nrf52. It uses app_timer, gpiote and adc. The power consumption in idle is ~30uA. Now I wanted to port this code...
FDS_VIRTUAL_PAGE_SIZE
The size of a virtual flash page.
Expressed in number of 4-byte words. By default, a virtual page is the same size as a physical page....
Hello,
I would like to use proxy_server(example of light_switch ) and ble_app_blinky_c, to make these two functions work together in one card. So this card can be controlled...
Hello everybody,
i have crated an Report id for the telephony usage on iOS from here https://opensource.apple.com/source/IOHIDFamily/IOHIDFamily-247/IOHIDFamily/IOHIDUsageTables...
Hello All,
I'm trying to program a NRF51822 module for the first time.Using Keil, Soft device s110_nrf51_8.0.0,soft device kit nRF51_SDK_9.0.0_2e23562 when I try to program...
I found the next response in a topic and i would like to know if there are some new improvements in the last SDK mesh 2.01.
devzone.nordicsemi.com/.../120547
I turn off...
I have installed from "nrfgostudio_win-64_1.21.2_installer" on Win-10 laptop. Weh I start nRFgoStudio, the main window appears for a second then I get a message "nrfgostudio...
Hi all, we're using code from this forum to enable GPIOTE and PPI to measure the low between the arrows to indicate a "start of transmission" and then switch to measuring...
Materiel and software use :
SDK mesh 2.0.0
SDK 15.0.0
NRF52832 with PCA10040 x5
Situation :
I would like to implement this network :
I follow the instruction...
I'm using the UARTE peripheral via the UART driver code in SDK v14.2. Due to transfer size and SoftDevice timing I have to use the double-buffered receive method (by calling...
Hello,
I am trying to make a beacon start advertising on a long press of a button. Using this as a reference, I implemented a timer as follows:
this is the flag to keep...
Hi!
I am using SDK15, my application is based on app_ble_uart. I have added my proprietary characteristic to NUS next to RX and TX Characteristic with quite a success. Now...
I use sdk14.2 nrf52832 as the primary, connect two iphone peripherals, iphone is connected to broadcast, when I turn on both peripherals, sometimes everything is normal, sometimes...
