Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi
I am porting another nRF52840 SPI OLED driver based on nRF5_SDK_14.2.0_17b948a\examples\peripheral\spi_master_using_nrf_spi_mngr
At first, it works fine without button...
hi guys ;
i have already an application on android phone that can read and write charchtéristic i also followed the tutorial Bluetooth low energy Characteristics, a beginner...
Hello
I am using nrf51822 .The function of DFU has worked well,but some weird problems puzzle me.
1、After DFU is successful,what is nrf51822's working state? Does it reset...
When I just plug the USB cable on the board I get a GPIO high voltage of 3V. But when I also put +5V on the external supply pins, the GPIO high voltages are 4.5 V. Is this...
Hi,
We are using nrf52832 board with sdk14.0. We are facing two issues:
Our use case is to send the data continuously when the notification is enable and stop...
The Bluetooth pairing is not working properly. I am developing the Application based on Bluetooth pairing with UART. Here I have included my concept and Program.Help me out...
Hi to everyone!
I have been getting the output of NRF_LOG_INFO functions through RTT in J-Link RTT Viewer terminal. The code has been executing in nRF52832DK.
Now I...
I have set up an nrf cloud and can control the led on pca10056 using the nrfcloud so configuring the gpio(pin no 7(Port P0.7))is becoming a problem.Can u provide me with a...
Hello,
I bought a nordic/wellcore ibeacon (nrf51822) to experiment. I want to enable all the features and would like to know what value to assign to the temparature enable...
Hello, i am using SDK12.2.0 and SD s130 on a nRF51822 (AC) and i am trying to add an external interrupt on a pin in the cscs ble_peripheral example. The code i am using (and...
Hi
We are using sdk version 12.2.0 and trying to change it to sdk 14.0.0. However, when I measured the power while converting the code, ppk confirmed that the sdk 14.0...
Hi all,
I'm using SD S132 v5.0.0 with SDK 14.0.
I'm testing now the BL buttonless DFU (and later the SD buttonless DFU) after working well with the app buttonless DFU...
I've implemented monitor mode debugging as described here and it works great. When I get a hard fault, it doesn't break in the IDE anymore. So it appears to be running fine...
I can connect the kit to the nrf cloud and even add the device to the gateway but i cannot switch on and off the leds.Where is the source code for the nrfcloud example?I cannot...
