Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hello,
here i explain the set up.
Cental_A Board :- scanning two peripheral
Peripheral_A Board :- advertise with name Peri_A .
Peripheral_B Board :- advertise with...
Hello,
I would like to know how I can check whether the SAADC is enabled or nor on my application. I am disabling the SAADC with nrf_drv_saadc_uninit(); after configuring...
I'm using the latest SDK (14.1) and have got a working COAP server running over BLE on a nRF52DK, and can exercise the service from my Ubuntu desktop without any problem....
Hai team,
Iam using the ble_app_beacon example program.
I found power profiling calculation on this link devzone.nordicsemi.com/.../ .
i calculated power consumption...
Hello,
I installed the new nrfjprog but it fails to write my nrf52 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with ERROR: argument...
Hello,i want to get the mac address by sd_ble_gap_address_get().There is a error message as fellow: Undefined symbol sd_ble_gap_address_get(referred from main.o). Where is...
HI!
The use of simulation software I2C and the sensor module communication in my program, without the use of the protocol stack, the normal running of the program, but after...
Hello,
I am using sdk 12.2.2 and pca10040. I want to include the mac address in adv packet name. I am not aware of the api used to get mac address. I used sd_ble_gap_address_get...
HW: BMD-350
SDK: nRF5_SDK_12.0.0_12f24da
Sample Code: examples\dfu\bootloader_secure\pca10040_debug
I have my own firmware app.
Problem:
If I use Keil to flash...
Do I have to temperature dissipation? I attached temperature sensor on my board with nrf51822. I removed copper layer of around the temperature sensor. But it seems the temperature...
Hi,
I am using nrf51822(qfaa), sdk12.3, softdevice s130.
I am using the ble_app_uart (both central and peripheral) as reference for my development.
I have both central...
Hi,
I get following error when i try to compile nRF5_IoT_SDK_v0.9.x for target nrf52822
compiling x509_csr.c...
assembling arm_startup_nrf51.s...
(13): error: A1517E...
I'm working with LEDs in a ble example
I'm calling ble_notification_init() and activate the LED in the callback handler.
I get sd_nvic_ClearPendingIRQ, sd_nvic_SetPriority...
